The water heater is a non-pressurized water heater. The hot water flows out naturally due to the height difference between the water tank and the water usage point. The output pressure is proportional to the height difference. If the height difference is too low, it will not function normally. In this case an effluent booster should be fitted. 6. When sunshine is not sufficient, to ensure effect, you should avoid using hot water several times in one day. 7. The energy source of this water heater

A). 3. Insert the vacuum tube with even force while rotating to turn it into the seal rings. The direction of the resultant force should be consistent with the axis of the vacuum tube. 4. Put the tail-holder into the tailstock (Fig. B) and then fasten the vacuum tube on the tail-holder (Fig. C). 5. The insertion depth of the vacuum tube into the seal ring should be about 1cm. Push the wind shroud onto the water tank to plug the joint (Fig. D). 6. When installing the vacuum tubes, one tube should

Features 1. SUS304 stainless steel water tank liner The tank liner is made of SUS304 stainless steel. It is a food grade material featuring high anti-corrosion ability and durability. 2. Effective and energy-saving heat insulation layer Polyurethane foam material for solar water heater is adopted to ensure high heat insulation ability and reduce heat loss to the maximum extent. 3. Al-Zn alloy coated tank shell Al-Zn alloy coated steel plate has very strong anti-corrosion ability and excellent we

5. Check valves should be installed on the trunks of water supply and drain pipes that are connected with the tap water pipe to prevent back flowing of water in the tank. 6. When several water heaters are combined, the installation plan should be validated by a professional service person of Haier. Installation instructions · Operation instructions • Connection method of water supply pipeline in the houses where a solar water heat coexists with another type of water heater To the tank of the sol

Vent Overflow Water inlet and outlet Tap water Check valve Operation instructions • FAQ Troubles Possible reasons Solutions No outlet water The water tank becomes empty Add water according to the time required in the instruction manual Disconnection or blockage of the pipeline or joints Repair the pipeline or remove the blockage No water comes from the overflow Broken vacuum tube(s) Replace the broken tube(s) pipe Water supply is stopped or water pressure is too low Wait until the water supply b

• Securing the bracket 1. Recommend you to secure the legs of the water heater on a foundation with embedded irons. You can also make cement bricks, attach expansion bolts in the cements and fix the heater legs on the expansion bolts. 2. Adjust the height of the bracket using the hard, waterproof spacers to ensure levelness of the water tank as well as even the load of each leg. Notes: 1. Ensure close contact of all legs of the water heater with the support plane. No legs are allowed to hang in

Any form of modification of the installation structure of the water heater may cause problems in use. 2. There are 5 ways for the heater pipeline to enter the house: flue, exhaust pipe, penetrating hole, special pipeline well for solar water heater, embedded bushing. Of which the first 3 are relatively popular. Before installing the pipeline, the installation personnel will discuss the entering way and installation position of the pipeline with you for your convenient use. During piping, the pen

2. Effective and energy-saving heat insulation layer Polyurethane foam material for solar water heater is adopted to ensure high heat insulation ability and reduce heat loss to the maximum extent. 3. Al-Zn alloy coated tank shell Al-Zn alloy coated steel plate has very strong anti-corrosion ability and excellent weatherability. It is the most preferred outdoor protective material. 4. Tower type bracket The bracket is made of carbon steel panel by shaping and plastic spraying. It has the advantag

If there is a shading object, the distance between it and the water heater should be longer than L. L=H/tg(66.5 -a) (where H: height of the shading object; a: local latitude) Note: Installation of the water heater must be conducted by professional personnel. 4 Installation instructions .. Outline and installation dimensions of the water heater Outline dimensions (in mm) Installation dimensions (in mm) Model A H D B S75ENF 1166 1457 1000 1351 S85ENF 1306 1457 1140 1351 S110ENF 1296 1710 1140 1590

2. Initial water filling shall be conducted in the morning or at night when there is insufficient sunlight. Filling water under strong sunshine should be avoided as this will cause explosion of the vacuum tubes. 3. If the water pressure is not high enough, normal water filling will not be realized. Please fit a booster. 4. To avoid burning, do not direct the shower nozzle towards your body while you are adjusting the water temperature. 5. The water heater is a non-pressurized water heater. The h