You’ve selected an amplifier that is one of the finest and most unique available on the market today. For 4-ohm loads, the APA5241 puts out 35 watts of continuous power on channels 1 through 4 and also delivers 100 watts of continuous power on channel 5. It also comes with the following features: ♦ Full frequency response with low distortion and exceptional signal-to-noise performance ♦ Advanced circuit design features bridgeable and mixed-mode operation for use in a variety of 5-, 4-, or 3-ch

This will protect the wire from being nicked and causing a short circuit. ♦ Extra cable can cause signal loss and act as an “antenna” for noise. Use only high-quality RCA cables that are no longer than necessary to make a direct connection with the source unit or equalizer. ♦ Depending on the type of system being installed, refer to the examples in Figures 4 through 6 (starting on page 6) for information on wiring and setting the operation mode. Installation ♦ 71 Clarion APAZI02 Power Cable

The APA4203 puts out 50 watts of continuous power into a 4-ohm load and delivers 75 watts (typical) into a 2-ohm load. The APA4162 is rated at 40 watts of continuous power or 65 watts (typical) for the same loads. Both models come with the following features: ♦ Full frequency response with low distortion and exceptional signal-to-noise performance ♦ Advanced circuit design features bridgeable and mixed-mode operation for use in a variety of 4-, 3-, or 2-channel systems ♦ Independent front/re

If you hear any noise, static, distortion or no sound at all, check the connections and refer to Troubleshooting. Depending on your system, the volume may become quite loud even at low level settings. Until you get an “audio feel” for the system’s power, use care when adjusting the controls. 3. Turn the balance controls to their extreme positions and listen to the results. Audio output should match control settings (audio from the left speaker when balance is left). 4. Increase the volume and ve

Sin embargo, no existe garantia de que no ocurrira interferencia en una instalacion en particular. Si este equipo causa interferencia danina a la recepcion de radio o television, lo cual puede determinarse encendiendo y apagando el equipo, se recomienda al usuario consultar al distribuidor o a un tecnico en radio y TV para obtener ayuda. Espanol 54 APX_DPX Amps.qxd 2/6/2008 11:53 AM Page 55 Contenido 1.CARACTERISTICAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

• Los circuitos avanzados proporcionan salidas puenteables para su uso en una variedad de aplicaciones. • Divisores de frecuencias electronicos independientes, cada uno con una pendiente de 12 dB por octava y rango de ajuste completo (de 50 Hz a 300 Hz) para ayudar al diseno del sistema de sonido. • Circuito de incremento de bajos para reforzar las senales de frecuencias que pudieran haberse perdido debido al diseno de la caja del subwoofer. • Controles de nivel de entrada ajustables con aislami

Alimentacion • Antes de comenzar, asegurese de que el interruptor de alimentacion de la unidad fuente esta apagado. .ADVERTENCIA! Para evitar cortocircuitos durante la instalacion,desconecte la terminal negativadelabateria del vehiculo antes de hacer cualquier conexion de energia. Fusibles • Para proteger el vehiculo contra incendio o colision en el caso de una colision, anada un fusible externo a la terminal de energia positiva (+) del amplificador y conectelo tan cerca como sea posible de la t

• Pulse-Width Modulated (PWM) MOSFET power supply for maximum performance with minimal distortion. • Remote turn-on with "soft start" muting to prevent turn-on "thump". • Advanced circuitry design featuring bridgeable and mixed mode operation for use in various system configurations including 4, 3, or 2 channel systems. • Variable high-pass/low-pass electronic crossover with a 12dB per octave slope (adjustable range: 55Hz to 5.5kHz). • Variable bass boost circuit to reinforce low frequency signa

SinAudio • Voltaje de encendido remoto bajo o ausente: compruebe las conexiones remotas en el amplificador y en la unidad fuente. • Fusible del amplificador fundido: reemplacelo con un fusible rapido nuevo (de la misma capacidad). • Cables de energia desconectados: compruebe la bateria y el cableado a tierra en el amplificador y compruebe las conexiones de la bateria. 73 Espanol APX_DPX Amps.qxd 2/6/2008 11:53 AM Page 74 • Terminales de los altavoces en cortocircuito: compruebe la continuidad de