(P.10) Headphones are plugged into the [PHONES] jack. RUnplug the headphones. .... Non-PCM The [CD IN (COAX)], [DIGITAL IN 1 (OPT)], [DIGITAL IN 2 (OPT)] or [DIGITAL IN 3 (COAX)] terminal is receiving non-PCM input singnals. (P.14–16) R.EQ ERROR1 Measurement failed because the room being measured is too noisy. RReduce the amount of ambient noise. R.EQ ERROR2 Measurement failed because there is no signal input to the microphone. UNLOCK The component connected to the [CD IN (COAX)], [DIGITAL IN 1

(AWG8) o mas, para evitar el deterioro del cable y danos en su revestimiento. • Para evitar cortocircuitos, nunca coloque ni deje objetos metalicos (por ejemplo, monedas o herramientas metalicas) dentro de la unidad. • Si nota que la unidad emite humos u olores extranos, desconecte inmediatamente la alimentacion y consulte con su distribuidor Kenwood. • No toque el aparato mientras lo utiliza porque su superficie se calienta y puede causar quemaduras si se toca. 2PRECAUCION Para evitar danos en

cables. • Protection circuit may be • Check connections by referring activated. to . (Blown fuse.) • Volume is too high. • Replace the fuse and use lower volume. • The speaker cord is shorted. • After check the speaker cord and fixing the cause of the short, replace the fuse. The output level is too The input sensitivity adjusting Adjust the control correctly small (or too large). control is not set to the correct referring to . position. The sound quality is bad.

• Check that no metal objects (coins, tools, etc.) are left inside the unit to avoid short circuits. • If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer. • Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched. 2 CAUTION Take the following precautions to keep the unit in proper working order. • Be sure the unit is connected to a 12V DC power supply with a negative ground connection. Accessories • Do not

• After installation, check that the brake lamps, winkers, and wipers work properly. Controls Operations of the following control and switches are required in accordance with the center unit and speakers connected with this unit. KAC-728 KAC-628 KAC-528 KAC-728 KAC-628 KAC-528 SPEAKER OUTPUT POWER AMPLIFIER 15 LPF FILTER OFF MONO(Lch)STEREO OPERATION GND INPUT SENSITIVITY(V) MAXMIN 0.30.5 1.0 L R LINE IN LEFT RIGHT SPEAKER LEVEL INPUT SPEAKER OUTPUT POWER AMPLIFIER 25 LPF FILTER HPF MONO(Lch)STE

КАС-6295 ....КАС-5298 Максимальная выходная мощность (4 Ом) Нормальное подключение........................... 200 Вт х 2........... 120 Вт х 2............80 Вт х 2 Мостовое подключение............................... 600 Вт х 1 ........... 350 Вт х 1 ............250 Вт х 1 Номинальная выходная мощность (4 Ом)............ Нормальное подключение (20 Гц - 20 кгц, ОГИ 0,08%).......................100 Вт х 2............60 Вт х 2.............40 Вт х 2 Нормальное подключение (Э1М45324, +В=14,4

4. Connect the speaker wires. 5. Connect the power wire, power control wire and grounding wire following this order. 6. Install the unit in the car. 7. Connect the negative -terminal of the battery. 2WARNING To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal. 2CAUTION • Be sure to turn the power off before changing the setting of any switch. • If the fuse blows, check wires for shorts, then replace the fuse with one of the sa