Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 0   Tamaño del archivo: 28 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name@name

NOTA: Si es dificil hacer girar la cadena o si se traba en la barra de guia, se ha aplicado demasiada tension y debe ajustarse como se describio en el paso 1. 3. Mientras ajusta la tension de la cadena, sostenga la punta de la barra hacia arriba y entonces apriete la manija del cerrojo de la barra (E). Siempre utilice guantes de trabajo pesado cuando maneje o haga ajustes en la cadena de la sierra. ADVERTENCIA: Si la cadena de la sierra se encuentra MUY SUELTA o MUY APRETADA, la rueda dentada, b

Descargado: 1   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

Failure to follow this procedure may result in injury to hand or fingers and may damage the starter mechanism. 5 10 feet 5a 6a Chain saw operating instructions For assembly follow the procedure in the appropriate section "Mounting Guide Bar and Chain" of this manual. DOLMAR chain, guide bar and sprocket must match each other (see the appropriate section in this manual). WARNING! Proper tension of the chain is extremely important. In order to avoid false setting the tensioning procedure must be f

Descargado: 6   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see „Starting the engine”). Hold the running chain saw approx. 6" (15 cm) above a trunk or the ground (use an appropriate base). If the lubrication is sufficient, you will see a light oil trace because oil will be flung off the sawing device. Pay attention to the direction the wind is blowing

Descargado: 5   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

Chain saws with significantly reduced kickback potential are available. 19 5 7 6 5 4 1 2 3 Lift the chain (6) over the sprocket (5). Using your right hand, guide the chain into the top guide groove on the guide bar (7). CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow! Position the guide bar (4) and push against the sprocket (5) as shown by the arrow. Mounting the guide bar and saw chain Use the universal wrench delivered with the chain saw

Descargado: 17   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

Always follow safety precautions in the Owner’s and Safety Manual. Improper use can cause serious injury! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Preserve this Manual carefully! ATTENTION! Suivez toujours les conseils de securite du present manuel d’emploi et de securite. Une utilisation incorrecte de la tronconneuse peut entrainer des blessures graves! Conservez avec soin ce manuel! Les g

Descargado: 0   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

The reaction of the chain drives the saw straight back toward the operator causing loss of saw control. Pushback fre-quently occurs when the top of the bar is used for cutting (fig. 14). 14 15 When felling in the vicinity of roads, railways and power lines, etc., take extra precautions (see fig. 16). Inform the police, utility company or railway authority before beginning to cut. 13 45° 45° = cutting down area 2 1 2 First clear the tree base and work area from inter- fering limbs and brush and c

Descargado: 5   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

See "Accessories" for the order number. Correct even the smallest excess height with a special flat file (1). See "Accessories" for the order number. Round off the front of the depth limiter (2). D C The sharpening angle of 25° must be identical for all cutters! Different angles result in a roughly, irregularly running chain, increase wear and tear and cause chain beakage. The front rake 60° of the cutter results from the cut depth of the round file. If the proper file is used in the right manne

Descargado: 1   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

A bottle brush can come in handy for cleaning out the cylinder ribs. With the cyinder fin cleaner, clean out the area between the cylinder fins and between the cylinder and the mounting plate. Do not use force. Be careful not to damage the short-circuit wire and the ignition wire. Mounting the fan housing Put the fan housing (13) on. Press the screws (14) into their holes. Lift the engine hood (15) slightly and use your thumb to hook in the tab (16) on the fan housing. Straighten out the fan hou

Descargado: 12   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

Kickback and other safety related precautions are described in detail within this owners manual. Additional owners manuals are available from DOLMAR POWER PRODUCTS, PO Box 5007, Alpharetta, GA, 30005-5007, USA, Telephone 1-888-OPE-PART. This product complies with: American National Standard Institute B 175.1-2000 chain saw safety standard. Canadian Standards Association Z62.1-95 chain saw safety standard. Z62.3-96 chain saw kickback standard. Society of Automotive Engineers SAEJ 335-Jun 95 „Mult

Descargado: 4   Tamaño del archivo: 8 mb   Fabricar: Dolmar  
Categoría: Benzo y sierras
@name@name

1). Never let the saw run unattended. Store it in a locked place away from children. Fill the fuel tank to 7/8 th full (see storing the saw). Do not lend your chain saw without this Owner’s and Safety Manual. Be sure that anyone using your saw understands the information given. Proper use of a chain saw involves 1. the operator 2. the saw 3. the use of the saw. Discription of symbols used on chain saws: CSA Standards Z62.1-03 C US Class 1B Z62.3-04 ANSI Standard B175.1-2000 SAE Standard SAE J335





Categoría