47927 (Rev. 9/11/08) 2 REPAIR PARTS FOR 45-0365 - PUSH SPIKE AERATOR REF QTY PART NO DESCRIPTION REF qty PART NO DESCRIPTION 1 1 24719 Frame Tray 11 2 46497 Spacer, 1.2" Long 2 5 24332 Spike Disk 11A 4 23368 Spacer, .75" Long 3 1 24720 Axle 12 4 R19212113 Washer 4 2 24369 Endplate 13 4 47141M Wingnut, M6 5 2 47925 Straight Handle Tube 14 4 45039M Carriage Bolt, M6 x 40 6 2 47926 Foot Tube 15 8 43182M Hex Bolt, M8 x 20 7 1 47924 Upper Handle Tube 16 8 47810M Nylock Nut, M8 8 7 741-0249

45-03621 45-03622 42" ROUGH CUT TRAILMOWER IMPORTANT: BATTERY REQUIRED!! The battery is NOT included with the deck but must be purchased separately. A 12 volt lawn tractor battery with 260/300 cold cranking amps and dimensions of 6-1/8"H x 7-5/8"L x 5-1/8"W is recommended to operate the machine. CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts FORM NO. 49463 (REV. 10/01/08) PRINTED IN USA 2 T

PULLEY CLUTCH LEVER PLUNGER REAR DRIVE.. COVER FOUR.. SCREWS CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clu

POLY PRO DROP SPREADER OWNERS MANUAL Model No. 45-02881 ™ • Safety • Assembly • Operation • Maintenance • Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully 175 LB. POLY PRO DROP SPREADER OWNERS MANUAL Model No. 45-02881 ™ the fastest way to purchase parts PRINTED IN U.S.A. FORM NO. 47717 (REV. 8/06) RULES FOR SAFE OPERATIONS Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all ti

Fasten the end plates to the corners of the tray using eight 5/16" x 3/4" hex bolts and 5/16" nylock nuts. Do not tighten till step 18. FIGURE 10 16. Place the lift handle through the slot in the tray. Fasten the lift handle to the smaller, inner hole in the middle wheel bracket using the bolt and nut which you pre- assembled earlier (figure 2). Fasten the lift handle to the larger, outer hole in the wheel bracket using a 3/8" x 1-1/4" hex bolt, the shoulder spacer, and a 3/8" nylock nut. Tighte

Este consciente del cambio de condiciones en las superficies inclinadas. Consulte las reglas de seguridad en el manual de propietario del vehiculo acerca de la operacion segura sobre superficies inclinadas. MANTENGASE FUERA DE LAS SUPERFICIES MUY INCLINADAS. 9. Siempre muevase hacia arriba o hacia abajo de una pendiente y nunca cruzando la pendiente. 10. Este equipo se debe operar a baja velocidad sobre terrenos escabrosos, a lo largo de arroyos y zanjas y sobre superficies inclinadas, para evit

4 OPERATION HAIR COTTER PINTRACTORHITCH PINOR MOWERCLEVIS PINREMOVE MOWER CLEVISPIN FROM THIS HOLE FIG. 5 OPERATION OPERATION GROUND LEVELCUTTING HEIGHTCUTTINGHEIGHTSHEIGHT ADJUSTMENT STRAPHEIGHT ADJUSTMENTLIFT LEVERLOCATING PINHAIR COTTER PINCLEVIS PINTOW BARADJUSTMENTTOW BARHAIR COTTER PIN1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" FIG. 6 OPERATION This mower has been designed to run offset from the center of the tow vehicle. This allows the operator to drive along side high brush with the tow veh

FORM NO. 49464 (5/04) CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts Agri-Fab. TABLE OF CONTENTS SAFETY RULES ...................................................... 3,4 SAFETY AND OPERATIONAL DECALS ................ 5,6 HARDWARE CHART .................................................. 7 ASSEMBLY ............................................................ 8-11 OPERATION.....................