And using this bagger cart is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating a bagger cart. You must use your own good judgement. You will find important safety information in a variety of forms,

Before installing or operating this equipment, read this manual and the owner’s manual supplied with the Honda riding mower or lawn tractor. This operator’s manual is considered a permanent part of the grass-bagging kit and should remain with the grass bagging kit if resold. The information in this publication was in effect at the time of printing. American Honda Motor Co., Inc. I reserves the right to change specifications or design at any time without notice and without incurring any obliga

4. Si equipe de ressorts. lever I'instrument et les accrocher. DEVERROUILLE VERROUILLE PLACE ON MALE QUICK HITCH (CANADA ONLY ) d ro AVOID SERIOUS PERSONAL INJURY WHEN ATTACHIN6 OR OETACHIWG IMPLEMENT POUR EVITER LES BLESSURES GRAVES: PLACE ON WALE QUICK HITCH LOCATE0 ON MALE QUICK HITCH (CANADA 'ONLY ) (US & CANADA ) -IMPORTANT:---------Before beginning assembly of this subframe, make sure tractor is on a level surface, parking brake is set and that engine is turned off, with key removed. su~ER

An accumulation of dry grass and leaves around the engine, the exhaust system, or on top of the mower deck (especially around the pulleys) may ignite. Always empty the grass bags when you finish mowing, even if they are not full. Stored lawn clippings are a fire hazard. '4 1. SAFETY IMPORTANT MESSAGE TO PARENTS YOUR CHILDREN'S SAFETY IS VERY IMPORTANT to Honda. That's why we urge you to read this message before letting your youngster operate a lawn tractor and mowing equipment. Lawn tractors and

NOTE: There are two additional 1 /4 inch washers below the rear belt cover mounting holes. Be carefull not to lose any of the washers. 3. Remove the two 6 x 12 mm flange bolts from the cover plate on the blower assembly. Remove the cover plate. 4. Unhook the blower drive belt from the mower deck pulley, then remove it from the blower assembly. NOTE: Observe the installed position of the blower drive belt, so you will be sure to replace it correctly. If the belt is reversed on the mower deck pull

All information in this publication is based on the latest product information available at the time of printing. Honda Power Equipment Mfg., Inc. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. This manual is a permanent part of the mower deck and lawn tractor, and it must stay with them if they are resold. READ THIS OPERATOR'S MANUAL CAREFULLY. Pay special attention to

For your convenience, a parts guide is also included in this publication. I NOTE: The information in this publication is based on the latest product information available at the time of printing. American Honda Motor Cb., Inc. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. Pay special attention to the statements preceded by the following symbols: ^DANGER Indicates t

Tighten the lift arm latch nut nut securely. 3. Install the reflectors. a. Clean the rear fenders where the reflectors are to be installed. b. Remove the protective backing from the two reflectors and press them firmly onto the rear fender as shown. 4. Secure the blade angle release cable by tightening the two cable ties. a. Verify that the blade angle release cable is routed over the coller tube, and between the front tractor bracket and axle as shown. b. Verify that the blade angle relea

1. Remove the filler cap/dipstick and wipe it clean. 2. Insert and remove the dipstick without screwing it into the filler opening. Check the oil level shown on the dipstick. OIL LEVEL 3.If the oil level is low, fill to the edge of the oil filler hole with the recommended oil (see page 21). To avoid overfilling or underfilling, be sure the engine is in a level position, as shown. NOTICE Engine Oil Change FILLER OPENING Drain the used oil while the engine is warm. Warm oil drains quickly and comp

All Rights Reserved Thank you for purchasing a Honda BK4148A side blower. This manual covers the operation, maintenance, and installation of the BK4148A side blower. For your convenience, this manual also includes a parts description guide, and warranty service information . Before installing or operating this equipment, read this operator’s manual and the owner’s manual s upplied with the tractor. As you read this manual, you will find information preceded by a INOTICE] symbol. That informâ