Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
Run the wire through the slots at the bottom right corner of the inner shroud. 8. Refasten the outer shroud to the inner duct assembly. {Inner Shroud} Outer Shroud Slot Slot ST194 Fig. 12 Position the fan to engage the inner shroud with the fan bracket slots and secure with sheet metal screws. 9. Install the snapstat by loosening the front screw on the inner side of the duct (Fig. 13) slide the snapstat under the head of the screw and tighten. Connect the leads to the snapstat. Make sure the snapstat assembly is mounted straight front to back. SnapstatLeft Air Duct ST671 Fig. 13 Install the snapstat and connect the extension wire terminals. View is with top removed, however, access is available through the rear when installing fan before gas line connection. 10. Slide shroud assembly over the sides and fasten the four screws loosened earlier. 11. Plug the power cord into a standard grounded 110 volt household outlet. If the fan control knob is not turned to the OFF position, the fan will turn on when the temperature at the snapstat reaches approximately 109°F. ST670 Vermont Castings Radiance Vent-Free Gas Heater Install ON/OFF Switch Rheostat Retaining Nut Control Knob ST347a Fig. 14 Attach rheostat to control panel. Valve may look different. MOTOR SNAPSTAT ON/OFF RHEOSTAT WHT WHT BLKBLKBLK GRN BLK POWER Disconnect powerbefore servicing. ST196 Fig. 15 #2767 / FK26 Fan Wiring Diagram WARNING The optional fan kit is equipped with a three- prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong outlet. Do not cut or remove the grounding prong from this plug. NOTE: If you are installing the fan kit after the stove is in its final location, follow same steps mentioned previously with the exception of disengaging only the right side of the outer shroud. The switch assembly parts are found in the parts bag. 1. Attach switch assembly to left rear side of stove shroud using two screws and existing holes in shroud. (Fig. 16) 2. Run wires down back of stove, under bottom of rear shroud to valve. 3. Attach wires to valve terminals. (Fig. 17) Switch Assembly Screws Existing Holes ST315 Fig. 16 Attach switch assembly to rear shroud. TP THTPTH Fig. 17 Attach switch wires to valve. ST228 Thermostat Connection (Optional) Use only a thermostat rated for 500 - 750 millivolts. Do not use low voltage (24V) thermostats. Check the table below for the appropriate gauge thermostat wire to use for the length of lead required in your installation. Thermostat Wire / Gauge Maximum Run 18 40 feet 20 25 feet 22 16 feet 1. Install the wall thermostat in the desired location and run the wires to the stove location. Terminate these leads with 1/4” female connectors. 2. Connect the thermostat wires to the valve. (Fig. 17) Vermont Castings Radiance Vent-Free Gas Heater 4. Replace burner. Slide the burner in at an angle with left side lower than the right side. Slide the left side onto the injectors, making sure the burner leg remains at a 90° angle to the base. (Fig. 19) Lower the right hand side down in to place. Make sure the burner is as far left as possible and the injector shoulders are inside the burner. OFF ON ThermopileBlack Black TP/TH TP TH On/Off Sw...
Otros modelos de este manual:Eléctrico - 3370 (519.25 kb)
Eléctrico - 3379 (519.25 kb)
Eléctrico - 3372 (519.25 kb)
Eléctrico - 3371 (519.25 kb)