We require that a licensed, bonded heating contractor install the unit and that a permit be obtained for the unit installation. Text Box: Text Box: GBU070 PELLET/CORN FURNACE Text Box: PINNACLE STOVE SALES INC. 1089 HIGHWAY 97 NORTH QUESNEL, BC. V2J 2Y3 TEL. (250) 992-5050 FAX. (250) 992-5850 E-MAIL info@pinnaclepellet.com 1 Rev: February, 02-20-2006 THIS MANUAL SUPERCEDES ALL PREVIOUS VERSIONS OF THIS MANUAL TABLE OF CONTENTS FURNACE SPECIFICATIONS pg 2 CONTROL AND COMPONENT FUNCTIONS pg 3 GENE

Slow Amber Flash - Normal operation with call for cooling. Two Amber Flashes - Normal operation with call for heat. Three Amber Flashes - Normal operation, burner is on at end of thermostat cycle. Six Amber Flashes - Normal operation with call for heat pump heating. Any Red Flash - Fault condition. NOTE: 4 or 5 flashes may indi cate a blown fuse on the circuit board. Application Upflow Downflow Horizontal Top 1" 0" 0" Vent 0" 0" 0" Rear 0" 0" 0" Side 0" 0" 1" Front* 0" 0" 0" Floor Combustible Co

If the furnace is equipped with NOx screens and is to be 7. To measure total static pressure, add supply duct pressure detailed information. used with LP (propane) gas, the screens must be removed to the return duct pressure, add pressure drop across the ‘A’ prior to start-up. coil, and add pressure drop across the filter. Ignore negative 2. Drip leg in the gas line must be installed. signs on the readings. 3. The furnace controls require correct polarity on the power 8. Inlet gas pressure shoul

If the furnace is equipped with NOx screens and is to be 7. To measure total static pressure, add supply duct pressure detailed information. used with LP (propane) gas, the screens must be removed to the return duct pressure, add pressure drop across the ‘A’ prior to start-up. coil, and add pressure drop across the filter. Ignore negative 2. Drip leg in the gas line must be installed. signs on the readings. 3. The furnace controls require correct polarity on the power 8. Inlet gas pressure shoul

Slow Amber Flash - Normal operation with call for cooling. Two Amber Flashes - Normal operation with call for heat. Three Amber Flashes - Normal operation, burner is on at end of thermostat cycle. Six Amber Flashes - Normal operation with call for heat pump heating. Any Red Flash - Fault condition. NOTE: 4 or 5 flashes may indi cate a blown fuse on the circuit board. Application Upflow Downflow Horizontal Top 1" 0" 0" Vent 0" 0" 0" Rear 0" 0" 0" Side 0" 0" 1" Front* 0" 0" 0" Floor Combustible Co

Theinstallationmustcomplywithregulationsoftheservinggassupplier, localbuilding, heating, plumbing, andothercodes. Inabsenceoflocalcodes, theinstallationmustcomplywithnationalcodesandallauthoritieshavingjurisdiction. B24.25” .56” .56” 20” 3” 23.8” .56” CombustionAirInlet2” DiameterVentConnectionOutletBDURINGINSTALLATION, DOORSMUSTREMAINONFURNACEWHENMOVINGORLIFTING. VentConnectionOutlet † Other airflows are available. see Tech Guide for all CFM options. * Cool Tap. ** Adjustment Tap. LED INDICATOR

FIGURE 11: Typical Suspended Furnace / Crawl Space Installation For modulating furnaces to be used in the downflow position, it is necessary to rotate the gas valve so that it is upright when the furnace is installed. Loosen the pipe union between the gas valve and manifold, rotate the valve as far upward as it will go, and tighten the union. See Figure 13, "Downflow Installation - Gas Valve Rotation". Angle Iron Bracket 6” Min. Between Rod & Front of Furnace 1” Max. Between Rod & Back of Furnac

Refer to “COMBUSTION AIR SOURCE FROM OUTDOORS and VENT AND SUPPLY AIR SAFETY CHECK” in these instructions for additional information and safety check procedure. 2. The duct shall be either metal, or a material meeting the class 1 requirements of CAN4-S110 Standard for Air Ducts. 3. The duct shall be least the same cross-sectional area as the free area of the air supply inlet opening to which it connects. 4. The duct shall terminate within 12 in (30.5 cm) above, and within 24 in (61 cm) horizonta

LO COMP Single Stage Compressor (OUT) O Reversing Valve Energized in Cool HI COMP Second Stage Compressor (OUT) Change Hot Heat Pump jumper on the heat pump control to “ON” if Hot Heat Pump Operation is desired. External Humidistat (Optional) Open on Humidity Rise 3 ID MODELS TM(8,L)M YM(8,L)M CM(8,L)M LM(8,L)M FIGURE 25: Thermostat Chart - Two Stage Heat Pump – Variable Speed or PSC Modulating Furnace Johnson Controls Unitary Products 368261-UIM-A-0508 18 Johnson Controls Unitary Products ACCES

The equivalent length of the vent system is the total length of straight pipe PLUS the equivalent length of all of the elbows. The following rules must also be followed: 1. Long radius (sweep) elbows are recommended. Standard elbows may be used, but since they have a longer equivalent length, they will reduce the total length of pipe that will be allowed. Short radius (plumbing vent) elbows are not allowed. The standard dimensions of the acceptable elbows are shown below. 2. The maximum equiv