CAUTION: Always follow proper shutdown procedure as described in this manual when turning the laminator off. CAUTION: The laminator may only be moved by a qualified service representative. Improper disconnection or reconnecting can result in injury to you and/ or damage to the laminator. CAUTION: Never use this machine for any other purpose than its intended design and function. You may be injured. The following actions can result in machine damage. CAUTION: Do not make any modifications to this

The DocuBind TL300 punches up to 12 sheets of 20 lb./80 gram paper at once. Punch only TWO clear covers at a time to prevent jams and excessive wear. 5. If punch jams, depress the RESET[2]button (D3). Then press the PUNCHES button (D2) again and remove paper or covers from punch throat (it may be necessary to punch several times in order to remove the paper). Repeat steps 1 to 4 with slightly less paper to avoid punch jams on additional lifts. Thank you lor purchasing the GBC DocuBind TL300. T

GBC 1264WF/1244WF Operation Manual © 2006 General Binding Corporation Page 18 Display Control Panel-Continued Top and Bottom Temperature Use the up or down arrow keys to increase or decrease the set temperature of the heat rollers. The temperature shown on the display is the temperature at which the unit is attempting to attain. For example if the unit is set to 200*F even though the actual roller temperature may be higher or lower. To view the actual temperature press MEASURE. Stop The STOP but

General Binding Corporation (GBC) is not liable for errors in this publication or for incidental or consequential damage in connection with the furnishing or use of the information in this publication, including, but not limited to, any implied warranty of fitness or merchantability for any particular use. GBC reserves the right to make changes to this publication and to the products described in it without notice. All specifications and information concerning products are subject to change with

Introduction Introduction 1-1 2. Getting to Know your Quantum P70iX Operating Controls 2-1 Plastic Covers 2-2 3. Operation Operating Controls 3-1 4. Options and Accessories Die Set 4-1 Die Set Storage 4-2 5. Home Screen Operation 5-1 Service 5-1 6. Maintenance Problem solving 6-1 Paper Jam 6-2 7. Specifications Specifications Quantum P70iX 7-1 Power Cord Specifications 7-2 Safety Information SAFETY MESSAGES The safety of you and others is very important to GBC. Important safety messages and info

DISPLAY 2 • Once the ProClick® Pronto™ ™™™™™ has measured the document thickness, the display will indicate the correct spine size to load into the machine. The example shown in Display 2 indicates “Small” under “Insert correct ProClick® spine size”. • The system will allow you to bind small documents with larger spine sizes. • Insert the appropriate spine cassette into spine slot as shown in Display 2. DISPLAY 3 DISPLAY 4 • Press “BIND” to bind your document and remove the document after you he

(Text Box comment Office Zone) (Text Box comment 800.543.5454) (Text Box comment ProClick Pronto® ™™™™™ ENG ProClick Pronto® ™™™™™ ENG 1.1 Safety Messages 1.0 Safety The safety of you and others is very important to GBC. Important safety messages and information are contained within this manual as well as on the machine itself. Please be certain to carefully read and understand all of these before operating the machine. The safety alert symbol precedes each safety message in this Operating Instr

Step 4. Figure 2 STAND BY CLEAR COUNTER START OPEN CLOSE NOTCH FUNCTION READY MANUAL AUTO PAD EMERGENCY 1 2 9 8 7 6 3 4 5 10 1 2 9 8 7 6 3 4 5 10 No. Symbol Function LED Display / Symbol Example 1 EMERGENCY Stops all the actions of the machine. Except when “HOT” shows on the LED display. “STOP” (flashing) 2 STAND BY / LED Temporarily lowers the temperature of glue tank so it won’t burn the glue when the machine is not operated. STBY00 3 CLOSE Closes clamp. 4 LED DISPLAY 1. The amount of books bo

Cada uno de estos componentes ha de cumplir la normativa europea de seguridad vigente. A efectos de seguridad, se indican las caracteristicas electricas (valores nominales) minimas del cable de alimentacion. NO UTILICE CONJUNTOS DE CABLE QUE NO CUMPLAN LOS SIGUIENTES REQUISITOS ELECTRICOS MINIMOS: ENCHUFE: 3 A, 250 V, 50/60 Hz, normativa europea de seguridad vigente. CORDON: Tipo H03VV-F3G0.75, armonizado ( < HAR > ). Los simbolos “< >” indican que el cordon cumple las normas europeas vigentes.

When using oversized covers, set the Edge Guide on Covers, punch all of the covers for your job and set aside. Move the Edge Guide back to the 11 ” setting to punch your contents then bind. 2. Raise lid on cover (D), and pull up appropriate selector pins to disengage punch pins that may nick the edge of your sheet. To determine which pins should be pulled up follow the punch steps indicated in section “D” using blank test paper. C. DETERMINE PLASTIC COMB SIZE 1. Slide the Binder Sizer open (C