Be 3® Quasar 12-Volt 2-Mile Navigational Light Without Wire Leads: 3100-3104, 3130-3134 With 7" Wire Leads: 3120-3124, 3150-3154 Attwood marine hardware, navigational lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s best-known boat manufacturers as original equipment. Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69385 Rev. B 03-10 Meets USCG CFR 183.810, ABYC A-16 requirements, an

Mount the anti-glare light in a position so that: • Light output is flat and parallel to water when boat is floating. • Light shines 360°, unobstructed. • Light does not shine on operator, or reflect off any part of the boat in the operator’s field of vision. Figure 1 7.5° or 39-3/8" One meter INSTALLATION Figure 2 Base #911339, 911370, or 911445 Pole Screw • Poles Without Locking Collar (5300 Series) 1. Align pole screw with slot in the existing base. Insert pole into base (Figure 2). 2. Press

Monroe Street, Lowell, MI 49331-0260 EXTENDING AND FOLDING THE POLE (5540 Series) The light is shipped with the pole folded and collars locked. 1. To unlock pole: Hold folded pole with lens upright. Pull the collar down (on lens half of the pole). Pull the opposite locking collar up. This separates the collars. (Figure 2) CAUTION: When unfolding pole, do not pinch fi ngers in hinge. 2. Press down fi rmly to engage electrical connectors. With Easy Lock Base, be sure locking spring clicks over pol

The lens completely encloses the bulb and socket for a splash resistant seal. Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable standards as tested by Imanna Labs, March 1997. 5040, 5045, and 5080 are Sidelights with 1 Nautical Mile visibility. 5940 and 5980 are All-Round Lights with 2 Nautical Mile visibility. All use Lamp 9235, #906, 13V, 6 Candle Power. REQUIRED FOR INSTALLATION • Cordless drill with 1/8", 3/8", and 3/4" (3, 10, and 19mm) bits. • Screwdriver. • Two #8 o

Rubber isolators are provided with each canister to allow for convenient installation. Vent Line Secure 5/8" vent hose with a clamp over each port (not included). Secure the vent hose as needed with hose mounting clamps for proper routing of hose and to ensure there is not stress on the hose at the connection to the canister. Integrated System Requirements Liquid fuel is not permitted to enter the canister. This can be managed by installing an in-line surge protector vertically +/- 45° as cl

Be 3® Quasar 12-Volt 2-Mile Navigational Light Without Wire Leads: 3100-3104, 3130-3134 With 7" Wire Leads: 3120-3124, 3150-3154 Attwood marine hardware, navigational lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s best-known boat manufacturers as original equipment. Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69385 Rev. B 03-10 Meets USCG CFR 183.810, ABYC A-16 requirements, an

For Sidelight Pairs, mark and drill a 3/4" (19mm) diameter hole on each side deck of the boat, equal distance from the bow. (Figure 3) 4. Thread wire leads and base stem into hole. Align centerline mark with straight-ahead position and mark location of screw holes. 5. Remove base and drill 1/8" (3mm) pilot holes for both screws. 6. Bring 12V DC (+) and (-) wires up through deck hole. Connect wires using waterproof crimp on butt joint connectors. 7. Activate light to verify proper operation. 8. A

• Removes rust drip stains and rust sprinkler deposits. PREMIUM MARINE POLISH • The ultimate protection for fiberglass, metal & painted surfaces • Last up to 6 times longer than other marine polishes • UV inhibitors help stop fading and oxidation • Leaves a super smooth, non-stick coating which reduces drag and repels dirt, grime, oil and stains • Race tested; increases hull speed • For medium to heavy oxidation use Premium Cleaner Wax BOAT WASH & WAX • Environmentally friendly, biodegradable fo