Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Homelite Tamaño del archivo: 1.96 mb Nombre del archivo: Idioma del manual:

nTighten Securely. CURVED SHAFT GRASS DEFLECTOR WITH EDGER GUIDE - TRIM ‘N EDGE ONLY EDGER GUIDE ASSEMBLY See Figure 4. nAssemble the two plastic pieces of the edger guide together using the short bolt, flat washer, lock washer and wing nut. nSlide the edger guide to adjust it to the desired trimming length. nTighten the wing nut securely. FRONT HANDLE WING NUT BOLT Fig. 2 BOLT GRASS DEFLECTOR BRACKET LOCK WASHER FLAT WASHER WING NUT Fig. 3 WING NUT LOCK WASHER EDGER GUIDE PIECES FLAT WASHER SHORT BOLT Fig. 4 ASSEMBLY CURVED SHAFT GRASS DEFLECTOR WITH EDGER GUIDE - TRIM ‘N EDGE ONLY See Figures 5 - 6. nRemove the wing nut, flat washer, lock washer, and bolt from the Owner’s Kit. nPlace the curved shaft grass deflector over the shaft and bracket. nSlide the assembled edger guide over the tabs on the grass deflector and bracket. nPlace the bolt through the slots in the tabs on the grass deflector and trimmer. NOTE: Ensure the slots are aligned before installing the bolt. nInstall the flat washer, lock washer and wing nut. nTighten the wing nut securely. STRAIGHT SHAFT GRASS DEFLECTOR - EASY REACH See Figure 7. nRemove the wing nut and clamp from the grass deflector. nAssemble straight shaft grass deflector to drive shaft so that the peg in the grass deflector fits in the locator hole in the lower side of the drive shaft near the gear head. nPlace the mounting bracket over the drive shaft so the square tab on the mounting bracket fits into the slot in the straight shaft grass deflector. nRotate the mounting bracket so the screw on the grass deflector goes into the slot on the mounting bracket. TABS ASSEMBLED EDGER GUIDE Fig. 5 WING NUT LOCK WASHER FLAT WASHER LONG BOLT Fig. 6 Fig. 7 OPERATION FUELING AND REFUELING THE TRIMMER FUEL MIXTURE This product is powered by a 2-cycle engine and requires pre- mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean 1 gallon container approved for gasoline. Recommended fuel: This engine is certified to operate on unleaded gasoline intended for automotive use. Mix Homelite Premium Exact Mix oil with gasoline according to the instructions on the package. If Premium Exact Mix oil is not available, use a high quality 2-cycle engine oil, mixed at 2.6 oz. per gallon (US). Do not use automotive oil or 2-cycle outboard oil. NOTE: Premium Exact Mixfuel mix will stay fresh up to 30 days. DO NOT mix quantities larger than usable in a 30 day period. FUEL MIXTURE OPERATING THE TRIMMER See Figure 8. WARNING: Always position the unit on the operator's right side. The use of the unit on the operator's left side will expose the user to hot surfaces and can result in possible burn injury. WARNING: To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. Hold the trimmer with the right hand on the rear handle and the left hand on the front handle. Keep a firm grip with both hands while in operation. Trimmer should be held at a comfortable position with the rear handle about hip height. Always operate trimmer at full throttle. Cut tall grass from the top down. This will prevent grass from wrapping around the shaft housing and string head which may cause damage from overheating. If grass becomes wrapped around the string head, STOP THE ENGINE, disconnect the spark plug wire, and remove the grass. Prolonged cutting at partial throttle will result in oil dripping from the muffler. PREMIUM EXACT MIX (50:1) GASOLINEOIL 1 gallon (US)2.6 oz. 1 Liter20 cc (20 ml) FILLING TANK nClean surface around fuel cap to prevent contamination. nLoosen fuel cap slowly. Rest the cap on a clean surface. nCarefully pour fuel into the tank. Avoid spillage. nPrior to replacing the fuel cap, clean and inspect the gasket. nImmediately replace fuel cap and hand tighten. Wipe up any fuel spillage. NOTE: It is normal for smoke to be emitted from a new engine after first use. WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. (9 m) from refueling site before starting engine. Do not smoke! OPERATING THE TRIMMER Fig. 8 OPERATION ADVANCING THE STRING String advance is controlled by tapping string head on grass while running engine at full throttle. 1.Run engine at full throttle. 2.Tap string head on ground to advance string. String advances each time the head is tapped. 3.Several taps may be required until string strikes the cut off blade. 4.Resume trimming. NOTE: If the string is worn too short you may not be able to advance the string by tapping it on the ground. If so, STOP THE ENGINE, and manually advance the string. ADVANCING THE STRING MANUALLY Push the spool retainer down while pulling on string(s) to manually advance the string. CUT OFF BLADE This trimmer is equipped with a cut-off blade on the grass deflector. For best cutting, advance string until it is trimmed to length by the cut-off blade. Advance string whenever you hear the engine running faster than norma...

Descargar ahora

Introduzca dos números de la imagen: