Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
IT IS THE RESPONSIBILITY OF THE OWNER TO MAKE SURE THE MIXER IS SET UP PROPERLY. THE FOLLOWING RECOMMENDATIONS SHOULD BE HELPFUL INSTALLATION TIPS 1. Be sure there is adequate clearance around the mixer for maintenance, repair and loading the mixer. 2. If the electronic weighing system is used, be sure that the weigh bars are kept clean and dry also items such as loading conveyors are not attached to or leaning on the mixer. Refer to scale manual for more specific information. 3. Mixer should be mounted on a structure of adequate strength to support a fully loaded mixer. Machine must be level and stable at the desired height. Weigh bar mounts should be fastened to this structure. 4. Manual door opener for the 3015 & 3020 can be mounted at either the front or the rear of the mixer. The following instructions will help To modify the door opener for operation from the opposite end: a. Remove latch and mounting bolt and install to opposite end of mixer in corresponding hole. b. Remove door wheel assembly. c. With door in fully closed position, cut door wheel shaft to proper length, drill mount hole, slide into position and replace bolt. 5. The , 3025, 3030, 3036, 3042, 3050, 3060, & 3070 manual door opener is in a fixed position on the drive end of the mixer. 6. An optional remote electric door actuator is also available for all models. The remote door actuator is standardon the 3095. ELECTRIC MOTOR RECOMMENDATIONS Following is a listing of suggested motor and frame sizes. Ratings are based on “normal dairy feed rations”. Heavier rations such as feedmill use, heavy/sticky beef rations, or industrial use, contact factory. A smaller motor may be adequate for easy-mixing materials, and a larger motor may be required for difficult materials*. Wiring and overload protection should be sized according to the motor size installed. The motor mount will fit the recommended motor size. Other motor sizes may require additional holes to be drilled in mount or a different mount. Dual motor mount, frame and shield are standard on 3025, 3030, 3036 & 3042 models. All models are designed to be used with a motor operating at 1725-1750 RPM. MODEL 3015 3020 3025 3030 3036 *HORSEPOWER 7.5 -10 10 10 10 -15 15 -20 MOTOR FRAME SIZE 213T 215T 215T 254T 254T 256T 254T 256T 256T 284T STANDARD MOTOR BUSHING 1-3/8” 1-3/8” 1-5/8” 1-5/8” 1-5/8” OPTIONAL MOTOR BUSHING 1-1/8” 1-5/8” 1-3/8” 1-3/8” 1-7/8” MODEL 3042 3050 3060 3070 3095 *HORSEPOWER 15 25 50 60 75 100 MOTOR FRAME SIZE 284T 286T 326T 364T 365T N/A STANDARD MOTOR BUSHING 1-7/8” 2-1/8” 2-3/8” 2-3/8” 2-7/8” OPTIONAL MOTOR BUSHING 2-1/8” 2-1/8” 2-3/8” 2-3/8” KUHN KNIGHT INC. 1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 MIXER SETUP IMPORTANT! READ BEFORE OPERATING MIXER. IT IS THE RESPONSIBILITY OF THE OWNER TO MAKE SURE THE MIXER IS SET UP PROPERLY. THE FOLLOWING RECOMMENDATIONS SHOULD BE HELPFUL SAFETY SHIELDING Be sure all shielding is in place and functioning properly...
Otros modelos de este manual:Mezcladoras - 3000 SERIES 3015 (384.42 kb)
Mezcladoras - 3000 SERIES 3015 (384.42 kb)
Mezcladoras - 3000 SERIES 3020 (384.42 kb)
Mezcladoras - 3000 SERIES 3020 (384.42 kb)