Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIONS MODEL: 3015 * * * shields removed for illustrative purposes 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIONS MODEL: 3020 * * * shields removed for illustrative purposes KUHN KNIGHT INC. 1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIONS MODELS: 3025 & 3030 * * * shields removed for illustrative purposes 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIONS MODELS: 3036 & 3042 * * * shields removed for illustrative purposes KUHN KNIGHT INC. 1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 LUBRICATION LUBRICATION LOCATION ILLUSTRATIONS MODELS: 3050, 3060, 3070 & 3095 * * * shields removed for illustrative purposes 3000STOPR005810R082503 TROUBLE SHOOTING This section is a condensed chart to help you if unsatisfactory operation occurs. To: use this chart : 1) Identify the problem (in bold) that best applies to you situation. 2) Find the “CAUSE” that seems most likely. 3) Perform the recommended “SOLUTION”. If you are unable to determine and correct the trouble, consult your authorized dealer PROBLEM: POOR MIXING PERFORMANCE, HAY IS WRAPPING ON AUGERS CROSS PIPES ON THE REEL ASSEMBLY ARE BENT, BELTS SLIPPING, SHEARBOLT FAILS, EXCESSIVE POWER REQUIREMENTS WHEN RUNNING MIXER CAUSE SOLUTION MIXER IS OVERLOADED HAY IS LOADED ON THE REEL SIDE OF THE MIXER BIG CHUNKS OF HAY CROSS PIPES SET IN THE OUTER POSITION HAY IS NOT FULLY CURED AUGER KNIVES ARE NOT SHARP HAY IS TOO LONG HAY PERCENTAGE IS TOO HIGH FOREIGN OBJECT IN MIXER IMPROPER LOADING SEQUENCE TOO MUCH FORAGE LOADED BEFORE MIXER IS STARTED Reduce load size, feed must be able to tumble from the reel cross pipes. If reel is over full, mixing action will be greatly reduced. Feed must not pile up between the reel and the side of the mixer. This causes a buildup of pressure, increases the power requirements of the mixer, and can cause pipes to bend. Load hay on the auger side of the mixer. This keeps hay from being caught between the reel pipes and side of mixer during initial loading. Break up bales before loading. Move reel cross pipes to the inner setting by compressing the springs and adding bolts and lock nuts in the reel arms. Do not move wiper arms in. See Mixer Setup section. Freshly baled hay tends to be green and does not tear apart easily. Allow hay to dry or cure longer before using in the mixer. Sharpen or replace knives when they become dull. Round baled and stacked hay cannot be used in the mixer unless it has been processed first. Some grassy types of hay must also be processed before it can be used. (See Mixer Operation section for more information) Mix a lower percentage of hay or change loading sequence. When mixing the hay, run the mixer at full rated PTO s...
Otros modelos de este manual:Mezcladoras - 3000 SERIES 3015 (384.42 kb)
Mezcladoras - 3000 SERIES 3015 (384.42 kb)
Mezcladoras - 3000 SERIES 3020 (384.42 kb)
Mezcladoras - 3000 SERIES 3020 (384.42 kb)