Votos - 3, Puntuación media: 4
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
p.8). DLIBRARY Accesses the INPUT CH page of the LIBRARY window. PM5DV2/DSP5D Editor Owner’s Manual 22 ..) 1 2 3 AHA GAIN Adjusts the gain of the internal HA (PM5D-RH model and DSP5D only) or of the external HA (AD8HR, AD824) patched to the input channel. The current setting is shown in the numerical box above the knob. You can also use the +48V button to switch phantom power on/off. You can use the GANG button to link the gain of two channels that are patched adjacent to each other, so that their current offset value will be maintained. BO (Phase) Inverts the phase of the signal after AD conversion. CHPF (High Pass Filter) Use the HPF button at the right to switch the high-pass filter on/off. You can use the knob at left to adjust the cutoff frequency. The current setting is shown in the numerical box above the knob. .GATE (except for FX RTN channels) 1 4 ML K N 2 9 J 6 3 8 7 5 AGate graph Indicates the approximate response for the gate of the currently selected channel. BGR meter This meter indicates the amount of gain reduction. CTYPE Indicates the type of the currently selected gate. DTHRESHOLD (Threshold level) Specifies the level at which the gate will open and close. The gate will open when the key-in signal exceeds this level, and will close when the signal falls below this level. ERANGE Specifies the amount by which the signal is attenuated while the gate is closed. PM5DV2/DSP5D Editor Owner’s Manual 23 FDECAY (Decay time) FDECAY (Decay time) GATTACK (Attack time) Specifies the time from when the key-in signal exceeds the threshold level until the gate opens. HHOLD (Hold time) Specifies the time that the gate will remain open after the key-in signal falls below the threshold. ION (On/off) This button switches the gate on/off. JLIBRARY This button accesses the gate library. Clicking this button will open the GATE page of the LIBRARY window. KLINK (Stereo link) This button links the parameter settings and key-in signals of adjacent odd-numbered/even-numbered input channels or the L/R sides of a ST IN channel, so that gating will operate in tandem for the two channels. LKEY IN SOURCE Select the desired key-in signal from the following choices. SELF PRE EQ The pre-EQ signal of the currently selected input channel SELF POST EQ The post-EQ signal of the currently selected input channel CH 1–48 POST EQ The post-EQ signal of the corresponding input channel (however, you can only choose channels belonging to the same group, within the seven groups CH1–8, CH9–16, CH17–24, CH25–32, CH33–40, CH41–48, and ST IN 1L/1R–4L/4R).ST IN 1L/1R – 4L/4R POST EQ MIX 21–24 OUT The output signal of the corresponding MIX channel immediately before the output attenuation MCUE This button cue-monitors the currently selected key-in signal. NKEY IN FILTER Select the type of filter applied to the selected key-in signal; HPF (high pass filter), BPF (band pass filter), or LPF (low pass filter). The ON/OFF button located immediately below switches the filter on/off. If you’ve selected BPF, use the two knobs at right to adjust the band pass frequency and Q. If you’ve selected HPF or LPF, use the knob at left to adjust the cutoff frequency. PM5DV2/DSP5D Editor Owner’s Manual 24 ..) 1 4 L N 2 J K 3 9 6 7 8 5 M ACompressor graph Indicates the approximate response for the compressor of the currently selected channel. BGR meter This meter indicates the amount of gain reduction produced by the compressor. CTYPE Indicates the type of the currently selected compressor. DTHRESHOLD (Threshold level) Specifies the threshold level at which the compressor will operate. The input signal will start being compressed when the key-in signal exceeds this level; compression will be removed when the signal falls below this level. ERATIO Specifies the ratio at which the input signal will be compressed when the key-in signal exceeds the threshold. FKNEE/WIDTH If the TYPE is COMP or EXPANDER, you can set the KNEE. The KNEE is the abruptness with which the output level will change. You can choose from HARD and 1–5. If the TYPE is COMPANDER H or COMPANDER S, you can set the WIDTH. The WIDTH is the spread between the boundary level of the compressor effect (THRESHOLD) and the boundary level of the expander effect. The expander effect will apply to levels that are lower than THRESHOLD+WIDTH. GATTACK (Attack time) Specifies the time from when the key-in signal exceeds the threshold level until the signal starts being compressed. HRELEASE (Release time) Specifies the time from when the key-in signal falls below the threshold level until compression is removed. IGAIN Adjusts the gain of the signal after it has passed through the compressor. JON (On/off) This button switches the compressor on/off. KLIBRARY This button accesses the compressor library. Clicking this button will open the COMP page of the LIBRARY window. LLINK (Stereo link) This button links the parameter settings and key-in signals of adjacent odd-numbered/even-numbered input channels or the L/R sides...
Otros modelos de este manual:Instrumentos Musicales - DSP5D (3.68 mb)
Instrumentos Musicales - PM5D-RH (3.68 mb)