Pay close attention to correct orientation of left and right hinges. Tighten securely. Insert tilt adjustment rods (F) into threaded barrels on each side frame. Screw adjustment knobs (E) into threaded barrels on each side frame. Set adjustment rods so that connecting brackets are about 2" above side frames for the time being with rods facing straight up and down and rear mounting brackets facing out, as shown in diagram. Tighten knobs securely. Base frame assembly is now complete. Set aside.

Use care not to drill all the way through the tabletop. ^5 Attach front hinges and rear brackets to tabletop using %" Phillips screws (I). Tighten securely but use care not to over tighten and strip. ©2008 ALVIN & COMPANY, INC. • P.O. Box 188, Windsor, CT 06095-0722 WWW.alvinCO.COm Phone: 860-243-8991 • Toll-Free: 800-444-2584 • Fax: 860-242-8037 • Toll-Free Fax: 800-777-2896 lit-abiss 7/qb

Hinges should also be centered evenly between left and right sides of tabletop. ^3 Adjust and position rear mounting brackets so they are 19/" from the front edge of the table top and centered evenly between left and right sides, as shown in diagram. Brackets should sit flush on the tabletop surface with the rods facing straight up and down. ^4 Mark locations of all 12 holes with a dark pencil or marker and then use an awl or drill with 1/i6" bit to make starter holes. Use care not to drill al

Use care to differentiate rear crossbar (B) (341/2" long) from footrest crossbar (C) (351/2" long). Attach both rear crossbars (B) and the footrest and support crossbars (C) to one side frame (A) using 2" Allen bolts (H). Tighten securely. Note: Threaded barrels preattached to leg frames must be in rear and facing out. Attach other side frame (A) to opposite ends of crossbars in step two using 2" Allen bolts (H). Tighten securely. Place dust cover (D) over top of base frame and attach using %

Use care to differentiate rear crossbar (B) (341/2" long) from footrest crossbar (C) (351/2" long). Attach both rear crossbars (B) and the footrest and support crossbars (C) to one side frame (A) using 2" Allen bolts (H). Tighten securely. Note: Threaded barrels preattached to leg frames must be in rear and facing out. Attach other side frame (A) to opposite ends of crossbars in step two using 2" Allen bolts (H). Tighten securely. Place dust cover (D) over top of base frame and attach using %

Carefully insert two front extension tubes (F) with attached brackets facing out. All four extension legs should be at their lowest position and locked with four height adjustment knobs (H). Set base aside. Front extension tube Figure 4 Figure 3 Place tabletop (B) with preferred side facing down on carpeted or protected floor. Place supplied cardboard template on board surface with edge of template at front edge of board. Left and right edges of template should be an equal distance from each

Make sure ends of back panel are snug against steel leg frames and holes are aligned in steel flange with pre-drilled holes in back panel. Attach using four 5/s" screws (I) supplied. Repeat step for right leg frame. Figure 2 5/s" Screws Floor Glide Figure 1 5/s" Screws □ Carefully remove base assembly from table/bench and place upright on floor. ^9 Place shelf (D) with predrilled holes facing up on the bench/table with 15 ends hanging over edge. Lift base assembly carefully (may require

Use care to differentiate the four crossbars from each other, as shown in the parts list. Also use care to differentiate left side frame from right, as shown in the parts list. Attach rear crossbars (B and C), footrest crossbar (E), and front crossbar (D) to one side frame (A) using 2" Allen bolts (G) to one) to one ). Pay close attention to correct orientation of all pre- drilled holes. Tighten securely. Attach other side frame to opposite ends of four crossbars in step two using 2" Allen bolts

XII-4-XB Tools Required: Phillips screwdriver, drill with VW bit. Parts Included: A 1pc Leg Frame B 1pc Tabletop C 2pcs Rear Extension Tubes (Shipped in separarate box) : D 2pcs Front Extension Tubes F 2pcs Height Adjustment Knobs To Assemble: Unpack all parts and inspect to confirm that all are present. Unfold base (A). Insert rear extension tubes (C) completely into frame (A) and loosely hand-tighten knobs (F). Insert front extension tubes (D) into frame (A). Place table top (B)

Align holes in front leg extensions (D) with holes in table top as shown in Figure 1. Fasten all 1/2" screws (H) and tighten securely. Use care not to overtighten and strip. Carefully return table assembly to the upright position. Adjust table top to desired height using height adjustment knobs (F). You’re finished and your table is ready to use as shown in Figure 2. Folding Table: Drop all extension tubes down to their lowest positions. Lift top up until the front extension tubes (D) diseng