MONITOR HOLD OFF 1 3 2 4 VOLUME TALK ACTIVE Program Additional Intercoms 1 2 Troubleshooting Intercom does not function. Check batteries in intercom. If using a DC Adapter ensure that it is plugged in. Ensure intercom is connected to a network. See Program. Ensure that intercoms are on the same channel. See Operation. The intercom can be programmed to at least one other intercom to become a network or it can be programmed into an existing network. CREATE NEW NETWORK Before programming, clear mem

An intercom on a channel can only hear an intercom on the same channel or on the paging channel. Conference Mode: Conference Mode allows multiple intercoms to participate in a conversation compared to Normal Mode in which only two intercoms can communicate. All intercoms must be set to the same channel or the paging channel to be in Conference Mode. To place intercoms in Conference Mode set Dipswitch #1 on block 2 to the UP position. Battery: When batteries are low intercom will emit two beeps e

Create New Network Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put the second intercom into Learn Mode (refer to the following table). Add to an Existing Network Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put any networked intercom into Learn Mode (refer to table below). Press and release the Talk button to verify network is complete. INTERCOM LEARN MODE Press the Learn button until a beep is heard. Press and hold b

The intercoms form an exclusive network and respond only to other intercoms in the network. Intercom (2 in Model RWIS) 1 Rubber Pads (2 in Model RWIS) Operation & Features Channel Button: Press the Channel button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. Volume: Pressing the V

These instructions are not intended to be comprehensive. Please consult the Keypad Programming Manual for complete information. © 2005 The Chamberlain Group, Inc. All Rights Reserved Guide for Programming the EL25 ProgrammingNumber Description of T ask Factor ySetting Programming Procedure *** Entering Programming Mode *** (6 Digit Password) 0 Exiting Programming Mode 0 # 1 Change or Verify the Unit's Password 000000 1 # (1 to change; 2 to verify) # (six-digit code) # 2 Set Unit ID Number and No

The intercoms form an exclusive network and respond only to other intercoms in the network. Intercom (2 in Model LSIS) Rubber Pads (2 in Model LSIS) Operation & Features Channel Select Button: Press the Channel Select button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. Battery: T

Intercom (2 in Model LSIS) Rubber Pads (2 in Model LSIS) Operation & Features Channel Select Button: Press the Channel Select button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel. Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use (Lithium bat

A cordless phone, cell phone, or other radio devices can also cause static. The intercom does not connect to another intercom and a green light is on longer than 3-1/2 minutes. The intercom is out of range. Place the intercom closer to the other intercoms in the network, with the antenna pointing up. The other intercom in the network has no power. Replace the batteries. The intercom has not completed programming. Clear the intercom's memory and reprogram. Need to clear intercom’s memory. Press a

Volume: Pressing the Volume DOWN button will lower the volume and pressing the Volume UP button will increase the volume. Intercom Models NLS1 & NLS1C (1) NLS2 & NLS2C (2) Rubber Pads Models NLS1 & NLS1C (1) NLS2 & NLS2C (2) MONITOR HOLD OFF 1 3 2 4 VOLUME TAL K ACTIVE Operation & Features Channel Select Button: Press the Channel Select button to set intercom to one of four secure channels or the paging channel. The default channel for the intercom is the paging channel where all four channel li

The intercom is compatible with various Chamberlain Wireless Products. Features On/Off: To turn intercom ON, press Talk button. To turn intercom OFF, hold down the Volume DOWN button for 3 seconds. Talk Button: Following the ringing of the doorbell by a guest, press and hold the Talk button to talk to the guest. Once the link to the doorbell is made, any other intercoms in the network cannot hear the conversation. Volume: Pressing the Volume DOWN button will lower the volume and pressing the Vol