13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired. 14. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replac

3 4 Verrouiller la gachette du pistolet. Tourner la vanne d’amorcage vers le bas. 5 Plonger le tuyau d’aspiration dans un seau metallique mis a la terre et rempli de liquide de rincage ; plonger le tuyau de vidange dans un seau jetable. Attacher le fil de terre au seau et a une veritable terre. 1 2 Compruebe que el interruptor de seleccion de funcion esta apagado (OFF). Enchufe el cable de alimentacion electrica a una toma electrica con conexion atierra. 3 4 Enganche el seguro del gatillo de la

Please retain for future reference SAFETY OPERATING INSTRUCTIONS PLEASE READ BEFORE USE . ALWAYS CHECK PAINT MANUFACTURERS THINNING INSTRUCTIONS BEFORE PROCEEDING. . ALWAYS CHECK PAINT MANUFACTURER’S INSTRUCTIONS FOR SURFACE PREPARATION. . ENSURE PAINT IS STIRRED THOROUGHLY BEFORE USE. . Never use corroded or damaged batteries, do not mix old and new batteries. . Do not overfill the paint reservoir. . NEVER use any liquids other than those specified. . Always ensure motor housing is firmly clipp

2) When you get to the end of the line, release the Trigger for a moment and then apply the product in the opposite direction just beneath the line you have sprayed. 3) Next, to achieve a vertical strip adjust the Spray Direction Plate (4) to the horizontal position then pull the Trigger and move your arm up and down over the horizontal strips you just have sprayed. Through gradual movement of the Spray Direction Plate (4) between Horizontal, Vertical and Round spray pattern you can vary the wid

• Do not allow bystanders in work area. •Do not point the sprayer nozzle in the direction of people or pets. • Pay attention to the direction of the wind, do not work against the wind. • Never use the sprayer during windy conditions. • Never point a sprayer nozzle toward an open flame to avoid the possibility of igniting the unit, causing injury to yourself or damage to surroundings. • Always release pressure in the pump prior to filling, cleaning, or servicing the sprayer. • Before opening a co

Please retain for future reference. 2 EXPLODED PARTS VIEW 13 14 14 13 Fig.2 12 11 10 9 7 8 4 5 6 2 3 1 A B Fig.1 Fig.3 HV3500 HV2900/ 3900 PARTS LIST FFiigg..11 No.Description Part Code No.Description Part Code 1. Needle and Fluid Tip Tool V0018 7. Fluid Needle 2.0mm V0006 2. Air Cap Ring V0001 8. Lip Seal -Fluid Needle V0007 3. Air Cap V0002 9. Paint Flow Adjuster V0011 4. Spray Direction Plate V0003 10. Paint Container Seal L0682 5. Fluid Tip 2.0mm V0004 11. Pick-up Tube V0012 6. Fluid Tip O-R

Disengage gun trigger safety. 5. Hold gun against grounded metal flushing pail. Trigger gun and increase fluid pressure 1/2 turn. Flush 1 minute. 6. Inspect for leaks. Do not stop leaks with hand or a rag! If leaks occur, perform Pressure Relief Procedure, page 8. Tighten fittings. Perform Startup, steps 1 - 5. If no leaks, proceed to step 7. 7. Place pump in paint pail. 8. Trigger gun again into flushing pail until paint appears. Move gun to paint pail and trigger for 20 seconds. Set gun safety

. No dirija nunca la pistola hacia personas o animales. . Use accesorios protectores adecuados, en especial proteccion respiratoria, gafas protectoras y guantes. . Evite el contacto directo de la piel y de los ojos con las soluciones anticorrosivas, de sellado de cavidades y de limpieza. . Mantenga a los ninos y a los animales domesticos lejos de la zona de trabajo. . El usuario debera estar descansado y concentrado en su trabajo. . La alimentacion de aire comprimido solo debe realizarse a trave

Example: P70DC2 is a 70:1 De-Ice, with built-in filter and no air control PxxxCxNotes: Packages sold with XSeal_LTH packings only. Packages sold with built-in filter only. Complete packages sold with XTR gun, 50 ft x 3/8 hose and 6 ft x 1/4 whip hose. Wall-mount packages are only available bare, but include 10 ft suction hose with 55 gal suction tube. Product Identifier: X=Xtreme Sprayer Motor Type: D: De-icing L: Low noise Mount Type: H: Heavy-duty cart L: Light-weight cart W: Wall-mount Packag