La serie de amplificadores AXP ofrece gran valor y excelente desempeño. Su instalación apropiada es esencial para un funcionamiento óptimo y confiabilidad a largo plazo. Por favor, lea atentamente este manual para familiarizarse con su amplificador y sus funciones. Servicio de Garantía Si su amplificador Jensen alguna vez necesita de un servicio, usted necesitará poseer el recibo original. Si alguna vez necesita devolver la unidad por cualquier motivo, siempre envíe el recibo con el producto.

1 Features......................................... 1 Installation........................................ 3 Wiring........................................... 5 Indicators and Controls.............................. 9 Testing...........................................11 Troubleshooting....................................11 Specifications.....................................11 Warranty.........................................11 Introduction Thank you for purchasing a Jensen amplifier. AX

RIGHT - LEFT - LEFT+ GREENWHITEGRAYBROWNBLACK CHASSIS GROUND ONRADIO -6 128-5721 128-5721128-5721128-5721128-5721128-5721SHT. 8 OF 12 SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12SHT. 8 OF 12 WARNING! l THIS AMPLIFIER IS DESIGNED FOR USE WITH 2 SPEAKERS l NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 1 SPEAKER. l NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. l FAILURE TO WIRE CORRECTLY MAY CAUSE DAMAGE TO THE AMPLIFIER. OUTPUT WIRING DIAGRAM OR GREASE FROM OR GREASE FROMOR GREASE FROMO

Tighten the screw down to secure the wire. 1. Power Connection The battery terminal (+12V) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse block) will reduce the power output and may cause noise and distortion. Use only #16 gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal of the battery after all other w

This wire should be as short as possible and any paint or rust at the grounding point should be scraped away to provide a clean metal surface to which the end of the ground wire can be screwed or bolted. 3. Remote Turn-On Connection The amplifier is turned on by applying +12 volts to the remote turn-on terminal (REM). The wire lead to this terminal should be connected to the "Auto-Antenna" lead from the car stereo which will provide the +12 volts only when the car stereo is turned on. If the car

We therefore advise that you read these instructions very carefully to familiarize yourself with the product and it's features. Should you require assistance with the installation or wiring of this unit, please call our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown. SPECIFICATIONS Maximum Output Power 4-Channel Operation: 125 watts x 4 2-Channel Operation: 500 watts x 2 Output Power @ 1% T.H.D. 4-Channel Operation: 600 watts RMS x 4 2-Channel Operation: 120 watts RMS x 2 Ou

Wire the speaker leads from the car stereo to the 5-pin adaptor harnesses as shown in the diagram (shielded cable is not required for this application) and plug the connectors into the mating High-Level Input socket on the amplifier. Carefully splice and insulate all wire connections. CAUTION: Use either the low-level or the high-level inputs on the amplifier. DO NOT use both input levels at the same time. -7 USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT, NOT BOTH. IMPORTANT RCA TYPE SHIELED CABLES (

INSTALLATION INSTRUCTIONS MOUNTING SURFACE DRILL 1/8" HOLE SELF-TAPPING SCREW WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a 4-Channel, 3-channel, 2-channel, or mixed-mono application. The following pages illustrate the input and output wiring for these types. Please refer to the appropriate diagrams for the system configuration you are using. The power and speaker wire connections for this amplifier are made via screw t

BRIDGED BRIDGED BATT REM GND CH1 CH2 CH3 CH4 FUSE LEFT SPEAKER OR SUB-WOOFER 4-8 OHMS RIGHT SPEAKER OR SUB-WOOFER 4-8 OHMS 2-CHANNEL MONO (BRIDGED) OUTPUT WIRING DIAGRAM USE #10 GAUGE WIRE (SEE TEXT) Power Indicator Lamps After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. If activated by a rise in emperature, the unit will resume operation after cooling off to a normal operating range.

Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess of 10 feet, #16 gauge is recommended. When wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain they correspond to the polarity of the correspondi