3. Use proteccion de los ojos y en las manos cuando maneje o aplique sustancias quimicas en los prados o en el jardin. 4. Lea las instrucciones y precauciones que encuentra en la etiqueta de las sustancias quimicas antes de manejar o aplicar dichas sustancias con la maquina. 5. Mantenga tuercas, pernos y tornillos adecuadamente apretados para asegurarse de que la unidad esta en condiciones de operacion segura. 6. Siga las instrucciones de mantenimiento y lubricacion segun se describen en este Ma

Shaft 2 20 1509-90 Bolt - 1/4-20 x 1-1/4" Hex Head 2 21 HA20137 Bearing 4 22 HA20145 Seal 1 23 HA20156 Bearing, Flange 2 24 HA20138 Cap, Bearing 3 *Standard Hardware - Purchased Locally REPAIR PARTS FOR MODEL 45-0308, 810-218 5 HP TOW BEHIND TILLER Ref. No. Part Number Description Qty. Req. 1 HA24000 Engine 1 2 HA22819 Guide - Belt 1 3 43085 Bolt, 5/16-18 x 1-1/2" Hex Head 4 4 HA115321 Screw, 5/16-18 x 5/16" Cup Pt. Set 1 5 HA11154 Key, Square 3/16" x 2" 1 6 HA20176 Pulley 1 7 HA2

No. Part Number Description Qty. Req. 47 HA3430 Hair Cotter Pin 2 48 HA20935 Tine Shield Assembly - RH 1 49 43062 Bolt, 3/8-16 x 1-1/2" Hex Head 4 50 HA20918 Wheel 2 51 R74780828 Bolt, 1/2-13 x 1-3/4" Hex Head 1 52 HA20670 Pivot Axle Assembly 1 53 *GM-126227 Bolt, 3/8-16 x 3/4" Carriage 4 54 HA20725 Strap Frame Extension 2 55 HA3433 Pin, Clevis 2 56 HA20690 Stake, Drag 1 57 HA446363 Washer 1 58 43177 Lockwasher, 1/4" Med. 1 59 HA20316 Plate, Fender Support 1 60 HA20941 Decal, Cauti

44483 (Rev. 4/90) RULES FOR SAFE OPERATIONS The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may result in personal injury. Always observe the rules of safe operation. 1. Do not allow anyone to operate the broadcast spreader without proper instructions. 2. Do not permit children to operate the broadcas

d. Set adjustable stop at "5". Pull flow control arm against stop. Verify that closure plate has opened about half way. e. If closure plate does not open half way, it may be closed too far at "OFF". Adjust position of flow control mounting bracket until closure plate will open about half way at "5" and still close when arm is locked in "OFF". Tighten 1/4" lock nuts. OFF ON 1234 678910 5 FLOW CONTROL ARM ON OFF AJDUSTABLE STOP SETTING "5" FIGURE 12 OPERATION HOW TO USE YOUR SPREADER SETTING THE F

45-02142 CAUTION: Read Rules for Safe Operation and Instructions Carefully 100 LB. PUSH BROADCAST SPREADER Assembly Operation Maintenance Repair Parts thefastestway topurchaseparts PRINTED IN U.S.A. FORM NO. 48319 (REV. 11/03) RULES FOR SAFE OPERATION The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may re

DESCRIPTION KEY QTY. DESCRIPTION A B C D E F G H I 6 2 2 1 8 2 2 4 8 Hex Bolt, 1/4-20 x 1-3/4" Hex Bolts, 3/8-16 x 1-1/4" Hex Bolt, 1/4-20 x 3/4" Carriage Bolt, 1/4-20 x 3/4" Hex Lock Nuts, 1/4-20 Thread Hex Lock Nuts, 3/8-16 Thread Lock Washers, 3/8" I.D Nylon Washer Flat Washer, 5/16" J K L M N O P Q R S 4 1 1 1 1 2 1 1 1 1 Flat Washers 1-5/8" Cotter Pin, 3/32" x 3/4" Cotter Pin, 1/8 x 1-1/2" Hair Cotter Pin, 1/8" Hitch Pin Spacers Nylon Wing Nut Adjustable Stop Flow Control Link Grip 3 5.Alig

4. Antes de llenar el esparcidor, mueva la palanca de control a la posicion “OFF” - cerrado. 5. Mueva el esparcidor a una superficie plana - una acera o una entrada al garaje - y llene el tanque de la unidad. 6. Ponga el Tope Ajustable en la graduacion deseada. 7. Pongaelesparcidorenmovimiento,y,luego,muevalapalanca de control hacia adelante hasta que quede contra el tope ajustable, antes de comenzar a rociar NOTA: Coloque siempre la palanca de control en la posicion “OFF” - cerrada -cuando este