Mower not level side to side, uncut or partially cut grass. 2. Blades dull or bent. 3.Carrier RPM too low. 4. Field conditions are so wet that the tractor tire is pushing grass into mud. 5. Ground speed too fast. 6. Blades lock back. 7. Blades riding up due to blade bolt wear or loose bolts. 8. Grass is down from previous weather conditions, 9. Possible build up of marerial under mower. Level 3 pt. Hitch linkage on tractor. Sharpen or replace blades. Use correct PTO speed. Too wet to

Replace any missing or illegible safety decals. Inspect for any damaged or worn parts and replace before next use. Store the Rough Cut Mower in a dry environment. 16 MAINTENANCE 1. Periodically check and maintain proper gear oil level. 2. Approximately every 8 hours, grease spindles (3), roller axle (1), wheel forks (4), wheel axles (4), PTO shaft universal joints (2), and PTO telescoping surface. NOTE: Use a high-temp/multi-purpose grease. 3. Before each use check to make sure all safety

Do not allow anyone to operate or assemble this equipment until they have read this manual and have developed a thorough understanding of the safety precautions and operation. Review safety instructions with all users annually. • This equipment is dangerous to children and anyone unfamiliar with its operation. The operator should be a responsible, properly qualified and physically able person familiar with farm machinery and competent in this equipment’s operation. • Never exceed the limits o

Corte irregular y dificultoso. Remedio Lime las cuchillas según el ángulo recomendado. Y Calibrador de alta profundidad causa Nunca se limaron los calibradores de profundidad. Resultado Corte lento. Se debe forzar la cadena para cortar. Causará desgaste excesivo del taco de la cuchilla. Remedio Baje los calibradores según la configuración recomendada. Gancho en el filo cortante de la cara lateral de la placa causa Posición de la lima muy baja o la lima era demasiado pequeña. Resultad

Estos procedimientos son pautas operativas para una operación segura bajo la mayoría de condiciones y no tienen el propósito de substituir las normas y/o leyes vigentes en su área. Si tiene alguna pregunta relacionada con su Serie 2510 o si no entiende alguna información contenida en este manual, consulte a su distribuidor Shindaiwa, quien le atenderá con gusto. También puede comunicarse con Shindaiwa Inc. a la dirección que aparece en la contra portada de este manual. Nunca operar la potadora

.aDVertenCia! Las emisiones liberadas por el escape del motor de este pro- ducto contienen substancias quimi- cas que, en el estado de California, son consideradas como causantes de cancer, defectos congenitos u otros efectos nocivos para la reproduccion. Indice PAGINA Declaraciones de seguridad ............. SP_2 Descripcion del producto .................. SP_6 Especificaciones................................. SP_6 Ensamblar........................................... SP_7 Instalacion y ajuste d

SRM-225U S/N: S79111001001 - S79111999999 Engine Cover, Starter......................................................................................................................................................4 Fuel System S/N: S79111001001 - S79111002122........................................................................................................6 Fuel System S/N: S79111005496 - S79111999999...........................................................................................

Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. CONTENTS Contents List items MODELS 2400/ 24001E 2410/ 24101E 1 - Power Head V V 1 • Drive Shaft Assembly V V 1 - PlasticBag (co-pack) V >/ -1, Operator's Manual V V -1, Safety Manual V V -1, Warranty Registration Card V V • 1, Limited Warranty Statement V V -1, Plastic shield V V -1,Tool Bag V V -1, 8mm x 10mm wrench V V -1, scrench V V -1, locking t

If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. Parts Required: Clamp, 4mm x 18mm Hexagon Head, Bolt, Link. 6. Remove shield and gear housing as an assembly. a. Loosen two (2) screws that clamp the gear housing to the drive shaft housing. b. Remove locating screw found at the top of the gear housing. Pull shield and gear housing assembly from the drive shaft assembly. IMPORTANT Prevent flexible drive cable from sliding f

Store unit in a dry, dust free place, out of the reach of children. DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark or serious personal injury may result. 2. Place the stop switch in the "OFF" position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. IMPORTANT Some tree sap and resins are corrosive. Thoroughly wash the guide bar and sprocket areas after each use, then coat metal parts with light oil. 4. Perform all pe