Box 2810 Tualatin, Oregon 97062 Telephone: 503 692-3070 FAX: 503 692-6696 Shindaiwa Kogyo Co., Ltd. Head Office: 6-2-11 Ozuka Nishi, Asaminami-ku Hiroshima, 731-3167, Japan Telephone: 81-82-849-2220 FAX: 81-82-849-2481 2002 Shindaiwa, Inc. Part Number 63888-94010 Printed in Japan Rev. 2/02 Specifications subject to change without notice. SHINDAIWA OWNER’S/ OPERATOR'S MANUAL P231 POLE PRUNER WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself wit

Light-weight for comfort, yet heavy-duty for performance, the ECHO TC-210i Tiller/Cultivator features ECHO's exclusive i-75™ system which reduces the required starting effort by 75%. This makes the TC-210i quite possibly the easiest to use of all your powered garden tools. Features include a 21.2 cc Power Boost Vortex™ engine with electronic ignition, quad port emission technology and a purge-pump-equipped carburetor for quick, dependable starts. A worm gear-type transmission provides high rpm a

Corte irregular y dificultoso. Remedio Lime las cuchillas según el ángulo recomendado. Y Calibrador de alta profundidad causa Nunca se limaron los calibradores de profundidad. Resultado Corte lento. Se debe forzar la cadena para cortar. Causará desgaste excesivo del taco de la cuchilla. Remedio Baje los calibradores según la configuración recomendada. Gancho en el filo cortante de la cara lateral de la placa causa Posición de la lima muy baja o la lima era demasiado pequeña. Resultad

SRM-260SB S/N 05001001 - 05999999 Engine, Short Block, Ignition, Cylinder Cover..............................................................................................................4 Starter, Fuel System........................................................................................................................................................6 Clutch, Fancase........................................................................................................................

Both must be read and understood for proper and safe operation. X770001105 X7702090605 10/12 IntroductIon Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages. the operator's manual Read and understand this manual before operation. Keep it in a safe place

• Always evaluate the branches to be pruned for hazards such as loose dead branches which may fall and strike the operator or helpers. Remove hazards before pruning. • Plan retreat path from falling objects. • Cut branches bounce when striking ground. • Check that shoulder harness is adjusted for safe, comfortable operation. See picture at right for proper adjustment. • Turn the Power PrunerTM off when moving from tree to tree. • Avoid any contact with saw chain. Avoid Hot Surfaces • Keep exhaus

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired. After refueling; • Wipe any spilled fuel from the unit. • Move at least 3 m (10 ft.) from refueling location before starting the engine. After use; • DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container. Storage Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precautio

3. Adjust handle position for comfortable operation, and tighten screws securely. 2-screw front handles 2. Position front handle on shaft and install Barrier Bar using two (2) 5x35 mm screws provided in kit. Handle must be at least 10 inches (250 mm) from center of rear handle grip. 3. Adjust handle position for comfortable operation, and tighten screws securely. NOTE The Barrier Bar is not a handle. blade InsTallaTIon Install Metal Shield 1. Loosely attach bracket (A) to shield (B) and attach t

Secure with two (2) 6mm x 30mm bolts. 9. Install hook. Three loop hook included with Blade Conversion Kit for blade use. Position 8 5/8 inch (220mm) from engine end of drive shaft assembly. DO NOT tighten at this time. 10. Install handles in bracket (G), place clamp top over handles and securewithfour(4)5mmx35mmbolts(H). 400 mm (15*3/4 In.) 220 mm (8-21/32 In.) ENGINE END 1SMEEHO. 11. Secure throttle cable and leads to drive shaft by sliding wedge under harness hook. 12. Install power h