Always wear: S A protective helmet where there is a risk of falling objects S Hearing protection S Approved eye protection Max. speed of output shaft, rpm Beware of thrown objects and ricochets. The operator of the machine shall ensure, while working, that no persons or animals come closer than 15 metres. Machines fitted with grass blades can be thrown violently to the side when the blade comes into contact with a fixed object. The blade is capable of amputating an arm or leg. Always keep people

WARNING: Always discard a blade that is bent, twisted, cracked, broken or damaged in any other way. Never attempt to straighten a twisted blade so that it can be reused. Only use original blades of the specified type. English- ---22 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s M

Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect in the bottom. An air filter that has been in use for a long time cannot be cleaned completely.The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced. Bevel gear The bev

530088185 11/11/02 Francais Avant d’utiliser cet appareil, veuillez lire attentivement les instructions et assurez--vous de les avoir comprises. Deutsch Lesen Sie diese Hinweise zur Handhabung des Gerats aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, da. Sie alle Anweisungen verstanden haben. Espanol Lea atentamente las instrucciones y asegurese de entenderlas antes de utilizar esta unidad. R 136/141 ENGLISH FRANCAIS DEUTSCH ESPANOL 2 IDENTIFICATION (WHAT IS WHAT?) 1 2 3 4 5 6 7

Then release the throttle lockout and throttle trigger. (A) Stop (B) Start (C) Stop switch STARTING AND STOPPING Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Choke: Set the choke control in the choke position. (1) Choke control (2) Choke position (3) Open position ! WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately. Ho

Never use a harness with a defective quick release catch. Quick release On the front is an easily accessible, quick release catch: • Pull out the red strap. • The hip strap and one shoulder strap will be automatically released at the same time and the harness and the engine unit will slide to the ground. Use this if the engine should catch fire or in any other emergency situation when you quickly need to take off the harness and machine. Equal load on shoulders A well matched saw and harness mak

English – 15 ASSEMBLY Fitting other guards and cutting attachments • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. CAUTION! Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. S

Now release the accelerator trigger (A) and then the throttle advance (B). WARNING: when the throttle advance is engaged, the head or blade rotates. 3) Move choke lever (E) to the closed position . 4) Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope until engine fires once. 5) Move choke lever (E) to the open position then pull starter rope until engine fires. Let engine run for a few seconds holding the trimmer. Now disengag

Never mix fuel in the brush cutter. 3. Place the brush cutter upright on the ground or on a sturdy bench and wipe any debris from around the fuel cap (Fig. J). 4. Unscrew the fuel tank cap and pour the mixture into the tank using a funnel (Fig. K). 5. Be careful not to spill any mixture. If this happens, wipe the spill with a clean rag. 6. Start the engine at least three metres away from the area where the fuel tank has been filled up in order to avoid any risk of fire. • Always use extreme care

101 87 70-27 SYMBOL EXPLANATION Symbols on the power cutter: WARNING! The power cutter can be dangerous! Careless and incorrect use can result in serious, even fatal injury. Read through the Operator's Manual carefully and understand the contents before you use the power cutter. Always use: • A protective helmet • Ear protection • Protective glasses or full face protection Symbols in the Operator's Manual: Checks and/or maintenance shall be carried out with the engine switched off, with the stop