Before using your new Kenmore machine, please pause for a moment and carefully read this booklet which contains instructions on how to operate and care for your machine. Specific instructions are gLven on threading, tension adjustments, cleaning, oiling, etc. This will help you obtain the best sewing results and avoid unnecessary service expense tor conditions beyond our control. Advtce on tile operation and care of your machine is always available at your nearest Sears Retail Store. Please reme

This will help you obtain the best sewing results and avoid unnecessary service expense for conditions beyond our control. Advice on the operation or need parts and service, J J Safety Cautions: • Be sure that the J o Disconnect the This eliminates • All covers must • Do not • Before • Do not e Handle e Closely pull the cleaning attempt the foot and care of your machine is always available at your always mention the model number and serial number electrical voltage of the wall outlet (wall recep

When using electrical appliances, basic safety precautions should be fol|owed, including the following: WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death° Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS Teach children not to play with control • Do not try to light any appliance! knobs or any other part of

The electrical equipment (motor, foot control, light, etc.) are warranted free from defects in material and workmanship for a period of two years from the date of original purchase. Non-durable parts including, without limitation, needles, belts, bobbins, bulbs, bobbin cases, shuttles, springs, and parts which normally require replacement are specifically excluded from this warranty. This warranty is void if: (a) This product has been cleaned, serviced, modified or tampered with by anyone other

Raise needle to its highest position and raise presser foot. Place darning plate over needle plate aligning two pins of darning plate with holes of needle plate. You may then determine the movement of the fabric yourself. See above for embroidery. BUTTONS ................................................ Model 377 Model 374 Model 373/372 Presser foot button foot - button foot Pattern selector 1-5(54321) - 4'6(lii) 1. Align two holes of button with slot of presser foot and lower foot to hold

The harder you press on the controller, the faster the machine runs. Note:*By releasing the controller, the machine stops running automatically. *Before using the machine, practice controlling the speed without threading. HOW TO REPLACE THE SEWING LAMP The sewing lamp is located behind the face plate. Remove the face plate by loosing the screw of the face plate. Bulb type: • To remove...Unscrew • To replace...Screw Note:*Before replacing a bulb, disconnect the machine from the power supply

3. 4. Following the slotted threading path, pull the thread down to the thread check spring (inside) and lead it across from left to right. 5. Pull the thread upward and slip into the slotted hole of thread take-up level from left to fight© . 6. Draw the thread through guides (6) and © , and thread the needle from front to rear®, leave the thread about 15cm(6 inches) long underneath the presser foot. B 10 DRAWING UP THE BOBBIN THREAD 1.Hold the end of the needle thread with your left hand

Remove lint and thread from all parts of shuttle and wipe with a lightly oiled cloth. To reassemble: Hold shuttle by center pin and fit carefully back into shuttle race, forming perfect circle with shuttle driver.. Replace retaining ring polished side out, making sure the bottom pin fits into notch. Lock retaining ring by turning levers back into position, Refit bobbin case with bobbin. 18 FREE ARM SEWING This sewing machine can be used like a flat bed machine, but easily converts to a fre

S.S. ) DECORATIVE EDGING Turn the ra w edgeunder 2cm a nd press. P lace the fabric rightsideup with the middle of the turnover under the center of the presser foot, so thatthe stitch s ews on to the fold a nd just aver the ta,w ed^e underneath. iW^IvWM SEWING BUTTONHOLES The built -in buttonhole mechanism of this machine makes it possible to sew button holes in a short time without turning the material. .................................................. Model 377/374 Model 373/372/372H P

The only responsibility of EURO-PRO Operating LLC, if any, is in relation to the specific obligations expressly assumed by it under the terms of this warranty bond. Please include proof of purchase. For repairs or replacement, send to: EURO-PRO Operating LLC, 4400 bois Franc, St. Laurent, Qc H4S 1A7, Tel.: (800) 361-4639 OWNERSHIP REGISTRATION CARD Please fill out and mail the product registration card within ten (10) days of purchase. The registration will enable us to contact you in the un