Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 0   Tamaño del archivo: 2 mb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

For a wider weld, draw the wire back and forth across the joint in a curve, this is called a weave bead. Note: If too much current is drawn from the Flux Wire Welder, the Thermal Overload protector will activate, the amber indicator will light, and the Arc Welder will turn off until it cools down. If this happens, turn the Power Switch to the OFF position and wait about 3 ~ 5 minutes. 9. After a few seconds, stop, switch off the welder, and check the progress. Compare your weld’s appearance with

Descargado: 4   Tamaño del archivo: 720 kb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

Also, some diseases that may be linked to exposure to welding or plasma cutting exhaust fumes are: • Early onset of Parkinson’s Disease • Heart disease • Ulcers • Damage to the reproductive organs • Inflammation of the small intestine or stomach • Kidney damage • Respiratory diseases such as emphysema, bronchitis, or pneumonia Use natural or forced air ventilation and wear a respirator approved by NIOSH to protect against the fumes produced to reduce the risk of developing the above illnesses. M

Descargado: 3   Tamaño del archivo: 2 mb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

Diagram.) WASHER HANDLE (#17) BOLT (#19) HEX NUT (#20) HANDLE BRACKET (#18) FIGURE C POWER SWITCH (#25) (#25) HEX SCREW (#16) FIGURE D To Attach Tong Tips To The Spot Welder: 1. Caution: Prior to attaching the Tong Tips (parts #48), make sure the Spot Welder is disconnected from its electrical power source. 2. To attach the Tong Tips (part #48) to the Upper and Lower Tongs (parts #46, #47), screw the Tips onto the Tongs as shown in Figure E. UPPER TONG (#46) LOWER TONG (#47) TONG TIP (#48) FIGUR

Descargado: 0   Tamaño del archivo: 2 mb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

Allow the Tong Tips (part #48) and the workpiece to cool before handling. (See Figures A, B, E, and Assy. Diagram.) 8. MAKE SURE THE WORKPIECE IS SECURED AT ALL TIMES DURING OPERATION. Use a vise, clamps, etcetera (not provided). 9. OVERUSE CAN CAUSE OVERHEATING. After continuous use, allow the Spot Welder adequate time to cool before the next use. 10. BEFORE TRYING NEW OR COMPLICATED TECHNIQUES, STUDY THE PROCEDURE, AND PRACTICE WITH SCRAP METAL. 11. ALWAYS DISCONNECT THE SPOT WELDER FROM ITS E

Descargado: 0   Tamaño del archivo: 658 kb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

Push in until the wire comes out the Welding Torch head. If it cannot be fed manually all the way out, it can be fed automatically when the welding unit is powered up. 6. Close the Feed Mechanism (10) over the wire, and adjust the feed tension (D) if necessary. 7. Check that +/– cables to connection Knobs (29) are correct. See photo (top-left). When using non-flux wire and protective gas, connect wire cables as shown in photo. For 0.9 flux cored wire, no gas is required. Reverse cable connection

Descargado: 0   Tamaño del archivo: 1 mb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

Unplug the Welder. Slightly tighten the Tension Adjusting Knob (10b) on the Wire Feed Assembly, and rewind the Welding Wire slightly before retrying. (See Figure E.) To check the tension on the Wire Feed Assembly, feed the Welding Wire against a piece of scrap wood from 2 to 3 inches away. If the Wire stops instead of bending, turn the Welder OFF. Unplug the unit from its electrical outlet. Then, slightly tighten the Tension Adjusting Knob (10b) on the Wire Feed Assembly. (See Figure E.) FIGURE

Descargado: 16   Tamaño del archivo: 243 kb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

START AIR FLOW BEFORE HEATING THE ELEMENT. CLOSE AIR FLOW AFTERTURNING OFF HEATING ELEMENT AND ALLOWING ITTOCOOL. 5. Always use pliers to change the tip on a welding gun. (Do not overtighten.) SKU 41592 Page 2 Rev 07/01 41S92 pSS 2 WJ/01, 9:12 AM —1111 I 1X1 '—I 6. Avoid working alone. If an accident happens, an assistant can bring help. 7. Avoid electrical shock. Do not use in wet environment, Do not use if electrical cord is damaged. 8. Avoid damaging gauge. Use only as specified in t

Descargado: 0   Tamaño del archivo: 2 mb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

Also, some diseases that may be linked to exposure to welding or plasma cutting gasses or fumes are: • Early onset of Parkinson’s Disease • Heart Disease• Damage to the reproductive organs • Ulcers• Inflammation of the small intestine or stomach • Kidney damage• Respiratory diseases such as emphysema, bronchitis or pneumoniaSafety precautions, such as using natural or forced air ventilation and wearing an ANSI approved respirator, are essential to reduce the risk of developing the above illnesse

Descargado: 0   Tamaño del archivo: 326 kb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

Assembly and Operating Instructions For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. Cut-Off Tool SKU 95028 For technical questions, please call 1-800-444-3353 Page Assembly and Operation Instructions (continued) note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension c

Descargado: 1   Tamaño del archivo: 1 mb   Fabricar: Harbor Freight Tools  
Categoría: Máquinas de soldar
@name

The RED Overload Indicator Light will illuminate and the Welder will automatically turn off until it cools down. If this happens, turn the Power Switch to its “OFF” position and wait approximately 20 minutes. (See Figure L.) Wire Speed Control Knob (17): 2. The Scale surrounding the Knob is relative value, not wire feed speed. (See Figure L.) Voltage Controls (18, 19): 3. Adjust the Voltage Controls based on thickness of metal being welded. (See Figure L.) If using solid-core wire, connect and s





Categoría