Children are not permitted to operate this machine. Connect to an earthed single-phase 230/240 V outlet, protected by a 16 A time-lag fuse. Operating other electric machines or appliances on the same circuit while welding is only possible to a very limited extent and not recommended. Earth and welding cable are firmly attached to the machine. Polarity does not matter with AC welding current. 13 Attach earth clamp to the workpiece, close to the weld seam and on bare metal for good conduction. Pla

Attention ! Priere de lire attentivement la presente notice avant l'installation et la mise en service. Oppassen! Lees deze instructies voor de installatie en ingebruikname aandachtig door. D DEUTSCH ENG ENGLISH KONFORMITATSERKLARUNG DECLARATION OF CONFORMITY Wir erklaren in alleiniger Verantwortlichkeit, da. dieses Produkt mit We herewith declare in our sole responsibility that this product den folgenden Normen ubereinstimmt* gema. den Bestimmungen complies with the following standards* der Ric

They keep in close contact with those who know best what good welding equipment is all about: the craftspeople. That is why a Metabo welding device has everything you need. That is a promise, because in addition to designing our welding equipment from start to finish, we also produce and assemble it - from the transformer to the entire electronics. The strictest of quality checks are therefore quite normal and the five year warranty on the main transformer is a logical conclusion. Metabo. Work.

1. F F Conservez le recu d'achat! La garantie ne peut etre accordee que sur France presentation de ce recu. 2. N N Oppbevar kvitteringen! Norge Garantiytelser skjer kun pa grunnlag av forelagt kvittering. 3. Sailyta ostokuitti! J Suomi/ Finland Takuu on voimassa vain kuittia vastaan. 4. S S Forvara kvittot! Sverige Garantiansprak erkannes endast mot uppvisande av kvitto. 5. Operation elements 1 2 3 4 5 1 Connection for torch (+) pole 2 Switch on/off and welding currant 3 Wire feed regulator 4 Ov

Welding outside in the rain is not permitted. Mains connection x Check to see that mains voltage matches the voltage shown on the machine's rating plate. x Set welding step switch to "0" before plugging in. Shielding gas cylinder connection x Place gas cylinder onto the welding machine's cylinder rack and secure with the chain to the cylinder holder at the rear of the unit. Take off the cylinder cap and open cylinder valve briefly, facing away from your body. x Screw pressure reducer to the gas

That makes welding devices real perfectionists: they can handle all metals from 0.3 mm on with direct or alternating current, depending on the material. Your advantage: They are so good at handling the concentrated splash-free electric arc, that bother- some reworking is now a thing of the past. Metabo wel- ding systems are produced as highly dependable tools: Only after successfully passing all air condition, dust chamber and vibration tests and then being checked again thoroughly, do they leav

For PA-liners with 4.7 mm outer diameter no support tube is required. 8. Attach torch lead assembly to machine and cut off (do not pinch off with cutting pliers) the PA-liner just in front of the feed roller. 9. The cutoff liner piece is installed between the wire spool and wire feed unit, to provide for easy guiding here too. 10. To thread the aluminium wire into the lead assembly temporarily remove the contact tip. Thread wire into liner. Set guide rollers to match wire diameter and pressur

duty cycle 60 % 60 % 100% duty cycle at 250 A 270 A Mains fuse T 16 A T 20 A Cooling F F Insulation class H H Protection class IP 21 IP 21 IP 21 Wire feed - - 4 roller drive Dimensions (Ixwxh) 1080x423x533 1080x423x533 737x420x240 Weight (with SDV) 130.3 kg 144.1 kg 24 kg Temperature range: operation -10 to +40 °C -10 to +40 °C -10 to +40 °C storage -20 to +70 °C -20 to +70 °C -20 to +70 °C Operating conditions: relative humidity 10-80 % 10 - 80 % 10 - 80 % Recommended welding t