If anything is missing, please do not return the product to the store. E-mail parts1@badgerbasket.com for assistance. STEP 1: See PICTURE 1. Remove the SHEET and MATTRESS (D, E) from the TOTE BED (A). Remove the inner fabric liner from inside the TOTE BED (A) by separating the hook and loop tape around the top, inner edge. Insert the FOUR RIB SUPPORTS (B) into the vertical pockets on the inside of the TOTE BED (A). There is one at the head, one at the foot, and one on either side. Replace the f

+01-360-859-5180, technics-APLA@nautilus.com | Printed in China | © 2007 Nautilus, Inc., All rights reserved. ™ and ® indicate a trademark or registered trademark. Nautilus, Inc. (trademarks include NAUTILUS®, BOWFLEX®, SCHWINN® and UNIVERSAL® and respective logos. Other trademarks are the property of their respective owners. Table of Contents Important Safety Instructions.............................................................................................................................

– Do not set up your tent under trees. – For best results in windy conditions, position the end of tent into the wind. 1 (2) Center Tent Poles (Black) (2) Side Tent Poles (Grey) (2) Rainfly Poles Layout & Positioning of Tent, Pole Assembly – Layout and position tent with doors facing desired direction. (illus. 1) – Stake down tent corners, using the tent stake loops. Keep the floor taut. (illus. 2) – Assemble all poles by interlocking shock-corded poles. – Insert the longer Center Frame Poles (b

9271-166 –Select a level campsite clear of Side Tent Poles rocks, branches and other hard Part No. 9271-167 or sharp objects. Screen Room Ridge Pole –Do not set up your tent Part No. 9271-162 under trees. Screen Room Upright Pole –For best results in windy Part No. 9271-168 conditions, position the end of Rainfly Pole tent into the wind. Part No. 9271-161 –See owners manual for more tips. Rainfly Part No. 9271-164 1 Layout & Positioning of Tent –Layout and position tent with screen room Illus. 1

9278B3681 Part No. 9278B3691 (2) Rainfly Poles Part No. 9278B3651 Rainfly Part No. 9278B3661 1 Layout & Positioning of Tent, Pole Assembly - Layout and position tent with door facing desired direction. (illus. 1) - Unzip door. - Stake down tent corners, using the tent stake loops. Keep the floor taut. (illus. 2) - Assemble all poles by interlocking shock-corded poles. - Insert the black poles into center pole sleeves marked with black binding. The poles should cross forming an “X” in th

5010000474 (1) Rear Pole (Blue Sticker) Part No. 5010000475 (2) Rear Brace Poles (Blue Sticker) Part No. 5010000476 (6) Center Upright Poles (Red Sticker) Part No. 5010000477 Rainfly Part No. 5010000481 1 Layout & Positioning of Tent - Layout and position tent with screen room facing desired direction. (illus. 1) - Stake down tent, starting with the corners. Do not stretch too tight. Angle the stakes slightly toward the tent. (illus. 2) Keep the floor taut. - Stake down the remainder o

Refer to the light manufacturer’s recommendations before operating your particular light in this position. 2. Do not leave the Lantern unattended when the light is on. 3. Use the light’s protective screen or shield at all times. 4. Use in a moderate temperature environment with good ventilation and spacing between multiple units. 5. Open the Lantern’s flaps for additional ventilation as required. 6. Maximum power capacity for these products is 500 watts in the 1880, 20” Lantern model, and 1

Repeat with each corner, sliding body further up pole each time until all poles slide into position (photo 3). Align poles with seams in body. Bank will now appear as shown in photo 4. 4. While pushing downward on Ring, bring internal cables up from inside body and place hooked ends in grooves in pole ferrules on opposite corners of Ring (photos 5 & 6) 5. Assembled Bank should appear as shown in photo 7. 1812 Valtec Lane, Boulder, CO 80301 303-444-8000 888-444-1812 fax 303-444-8303 salesinfo@

9180B3151_ Poles (1) Rainfly Part No. 9180B3251 Pole Rainfly Part No. 9180B3351 1 Layout & Positioning of Tent, Pole Assembly - Layout and position tent with door facing desired direction. (illus. 1) - Unzip door. - Stake down tent corners only, using the rings at the end of the stake loops. (illus.2) Keep the floor taut. - Assemble frame poles by interlocking shock-corded poles. This will make two long poles. - Insert the poles diagonally into pole sleeves. The center of the poles sho

– Do not set up your tent under trees. – For best results in windy conditions, (2) Rainfly Poles position the end of tent into the wind. Hinged Door Pole Vertical Hinged Door Pole Rainfly Part No. 9278-1091 1 Layout & Positioning of Tent, Pole Assembly – Layout and position tent with door facing desired direction. (illus. 1) – Unzip door. – Stake down tent corners, using the tent stake loops. Keep the floor taut. (illus. 2) – Assemble all poles by interlocking shock- corded poles. – Insert the b