Mire si se producen burbujas. Escuche por un ruido de gas escapando. Sienta por si hay un frio extremo. Huela por un olor a huevo podrido. No use una llama. No la use si hay una fuga. • Usela solamente como un aparato para alumbrar. No altere nunca en ninguna manera o no la use con ningun aparato o pieza que no este expresamente aprobado por Coleman. • No la use nunca como una estufa para calentar un lugar. • Usela siempre parada en posicion derecha. Proteja el cilindro de un calor excesivo. PEL

• Work in a fully ventilated area. • Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer. • Decide which seams need to be sealed. Seams that will be exposed to rain, runoff, or ground level water are a must for sealing, seams on uncoated nylon or mesh panels don’t need treatment. There is no need to seal the seams in the roof or the factory taped seams. We recommend sealing both floor and fly seams and reinforcements. • Apply sealant to t

Tie a piece of cord or web into a loop through the ring to be used as a large stake loop if needed. • With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs. • Do not attempt to remove the stakes by pulling on the tent becket loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Ro

CLEANING: • Clean the tent by setting it up and wiping it down with a mild soap (liquid hand soap) and lukewarm water solution. Rinse thoroughly and dry completely. Never use detergent, washing machines or dryers because they can damage the tent’s protective coating and seams. After cleaning, be sure the tent is completely dry, especially the heavier, double-stitched areas such as the seams, before storing or mold / mildew are likely to grow. • Clean the tent poles with a cloth and lubricate the

Pull the tent into a rough hexagon. Do not stake down the tent just yet; but in windy conditions, stake down one corner that faces into the wind. 2 Assemble the shockcorded tent poles and rod. Carefully seat each section. Try to keep the poles from snapping together as this can damage the ends. Set the shorter vestibule rod aside. 3 Insert the tent poles into the mesh sleeves. • Near the side of the door, insert and slide a pole through the continuous mesh sleeve from A to B. Push the pole rathe

(Press the RECOVERY button again to return the main display.) TEMPERATURE: Screen will display room temperature in sleep mode. ScoreConditionHeartRate(fromtestHRminusendHR) F1ExcellentAbove50F2Good40~49F3Average30~39F4Fair20~29F5Poor10~19F6VeryPoorUnder10 Console Information GENERAL INFORMATION: 1. Start pedaling or press any button to start Console. 2. The console will shut down after 4 minutes of no activity, and will display room temperature. Begin pedaling or press any button to bring consol

AVERTENCIA • PELIGRO DE QUEMADURAS • No deje nunca la lampara desatendida cuando este caliente o en uso. • Mantengala fuera del alcance de los ninos. Espanol-2 Espanol-3 PELIGRO • PELIGRO DE MONOXIDO DE CARBONO • Esta lampara es un aparato de combustion. Todos los aparatos de combustion producen monoxido de carbono (CO) durante el proceso de combustion. Este producto esta disenado para producir cantidades extremadamente diminutas y no peligrosas de (CO) si se usa y mantiene de acuerdo con todas

(Fig. 10) Fig. 11 .. Deslice los estuches a la misma vez y girelos hasta que el simbolo de punto “ “ sobre el estuche superior para cargar quede alineado con el simbolo de cerrado “ “. (Fig. 11) Fig. 10 Estuche Inferior para Cargar Estuche Superior para Cargar Para Instalar Mantillas Fig. 13 Fig. 14 .. Mueva hacia la izquierda la Palanca Liberadora hasta que la palanca quede por encima del simbolo de abierto QuickLift™ “ “. (Fig. 13) .. Quite cuidadosamente la cabeza de la lampara separandola de

Do not bounce tent bag on its end to get the tent out. These actions may cut the shock cord and/or damage the pole ends. 1. Unroll and unfold the tent and lay it on the ground. In windy conditions, stake down one front corner into wind. See fig.1. 3. Fit the posts into the grommets: There are webs and grommets sewn to each corner of the tent. Start at either end and insert the locking posts from the base of the frame poles into one of the grommets. Repeat at the opposite end, raising the frame a

Start at one end and drag the fly up and over the top of the tent [works best with two people]. It only fits one way; align the yellow web of the fly to the yellow web on the tent. See fig.8. • Reach under the fly and wrap all the Velcro® straps around the poles to secure the fly to the frame. See fig. 9. Stake down the y: • There are, web/ring assemblies on the bottom at each side of the fly vestibule door. Pull these out and away from the tent and to stake down. Adjust as necessary. See fig.10