Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
HP Large Form Factor Disk
8.
Remove the top access panel:
a.
Lift the access panel latch (1). The access panel
Enclosure Backplane
About this document
Removing the backplane
will slightly disengage from the enclosure.
Replacement Instructions
For the latest product documentation, go to http://
1.
Schedule a maintenance window.
b.
Slide the access panel to the rear (2) and lift
www.hp.com/support/manuals, and select your product.
2.
Stop all I/O to the enclosure.
away from the chassis.
WARRANTY STATEMENT: To obtain a copy of the
3.
Power down the enclosure by pressing and holding
warranty for this product, see the warranty information
the On/Standby button on the rear of the disk
This document details procedures for replacing a failed
backplane in an HP Large Form Factor (LFF) Disk Enclosure.
website: http://www.hp.com/go/storagewarranty
enclosure until the system power LED changes from
green to amber.
4.
Remove all cabling from the rear of the enclosure.
Ensure all cabling is marked to facilitate re-cabling
Before you begin
later.
The backplane is located inside the chassis of the disk
5.
Label drives with the drive bay identification labels
enclosure. Observe the following precautions when
included in the replacement kit.
replacing the backplane.
CAUTION:
Reinstalling a drive in a drive
9.
Disengage both I/O modules, to gain access to the
CAUTION:
bay other than the one from which it was
backplane:
•
To avoid damaging backplane components
removed may cause data loss.
a.
Squeeze the button on the bottom of the locking
and LEDs, use care when handling the
Apply the appropriate drive bay identification label
lever (1) and rotate out the handle (2).
backplane.
to the handle of each drive.
b.
Position one hand under the module, and with
•
These procedures require that all drives be
the other hand, pull the module out of the
Table 1 LFF disk enclosure drive bay layout
removed from the enclosure and returned to
enclosure (3).
their original drive bays. If this is not possible,
1
4
7
10
two people are required to remove the
enclosure from the rack, to prevent bodily
2
5
8
11
injury.
3
6
9
12
•
Parts can be damaged by electrostatic
discharge. Use proper anti-static protection.
6.
Remove all drives from the enclosure.
Keep parts in electrostatic containers until
IMPORTANT:
Remove the drives in
needed and ensure you are properly
bay-number sequence and place them on
grounded when touching static-sensitive
your work surface in the same order. This
components. For more information, see the
ensures that you reinstall the drives in their
product user guide.
original drive bays. Reinstalling drives in
10. Disconnect all cables from the backplane.
drive bays other than the ones from which
NOTE:
Information about this component is also
they were removed may cause data loss.
available on the hood label.
© Copyright 2009, 2011 Hewlett-Packard Development Company, L.P.
Press the release button on the lever (1) and rotate
Printed in the US
the lever to the left (2). Then, pull the drive out of
the drive bay (3).
Verifying component failure
Use the following methods to verify component failure:
•
Analyze any failure messages received. HP fault
monitoring software provides a recommended
action.
Part number: 513752-005
July 2011
•
edition: Fifth
*513752-005*
View Onboard Administrator system and device
status displays for Critical, Major, Minor, and
Warning icons. For more information, see the HP
BladeSystem Onboard Administrator User Guide.
•
Check the enclosure status LEDs:
7.
Loosen the thumbscrews that secure the enclosure
◦
Green: Normal operation
to the front of the rack and remove the enclosure
◦
Amber: Fault condition
from the rack.
Page 1
...Otros modelos de este manual:
datos de dispositivos de procesamiento - HP D2600 Disk Enclosure/S-Buy (674.53 kb)
datos de dispositivos de procesamiento - HP D2600 w/6 2TB 6G SAS 7.2K LFF DP MDL HDD 12TB Bundle (674.53 kb)
datos de dispositivos de procesamiento - HP D2600 w/6 3TB 6G SAS 7.2K LFF Dual port MDL HDD 18TB Bundle (674.53 kb)
datos de dispositivos de procesamiento - HP D2600 w/6 450GB 6G SAS 15K LFF Dual Port Enterprise HDD 2.7TB Bundle (674.53 kb)