Iniciar sesión:
Clasificado: Nombre ↓   Descargas   Tarifa   Tamaño ↑  
Descargado: 1   Tamaño del archivo: 292 kb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

Always mount the amplifier in a place that protects the amplifier from the elements. In addition, mount the amplifier on a stable, flat surface. NOTE: Mounting amplifiers upside down is not recommended and may cause premature thermal shutdown. WARNING! Do not mount any amplifier in the engine compartment. Amplifiers are not designed to endure the harsh environment of the exterior elements. Passenger Compartment If you are going to mount the amplifier in the passenger compartment, make sure you h

Descargado: 6   Tamaño del archivo: 2 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

(When ORION amplifiers are not used, the ORION PPS 100 Phantom Power Supply is required.) LOWS AMPLIFIER SUBWOOFERS This diagram shows a method for summing only the lows and permitting the midrange and highs to remain in stereo. In this system, an ORION 200 CRX Active Crossover is used to separate the lows from the highs as described in figure 5, and the 400 BDG Bridging Module is connected only to the lows side. In this way, the midrange and high frequencies are applied to the highs amplifie

Descargado: 14   Tamaño del archivo: 3 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

This mode can be used to provide more power to the subwoofer while maintaining stereo left and right. In this system, the 400 BDG Bridging Module accepts the stereo inputs and turns one channel over 180 degrees (inverts the channel). Both channel outputs of the amplifier are now connected to the subwoofer with the inverted channel being used as the negative input. This works because the two channels are 180 degrees out-of-phase. The left mid/high speaker is connected normally, but the connecti

Descargado: 102   Tamaño del archivo: 2 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

If you only have 1 set of RCA outputs from your - Refer to the section “Settings for Best Performance” headunit, you can simply connect those to the inputs for ch 1/2 and switch the MODE to Minimum final loudspeaker impedances: 2ch. The amplifier will auto sum the signal and provide mono output for bridged - 2 ohm per channel in stereo mode. channels 3/4. - 4 ohm mono bridged. POWEGRN IDN P U TREM BA TT+12V Ch4 Ch3 Ch2 Ch1 - + - + - + - + BRIDGED BRIDGED FUSE STEREO LINE INPUT MONO LINE INPUT IN

Descargado: 16   Tamaño del archivo: 2 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

- LINE OUTPUT: Full range RCA pass through. 2 Channel Full Range Stereo: Interconnect cable checklist: Control checklist: - Connect the two inputs of the amplifier to a Radio/CD with quality RCA cables. - Refer to the section “Settings for Best Performance” Switch setting checklist: - 1/2CH X-OVER: FULL Minimum final loudspeaker impedances: Mono Operation: - You can also feed the SAME signal to both left and right inputs via a Y-adapter RCA cable. - Connect the mono speaker positive terminal to

Descargado: 7   Tamaño del archivo: 2 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

Lower power amplifiers will clip earlier than their more powerful cousins, and cause loudspeaker failure when overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils. Amplifiers should be mounted with the fins running horizontally for best convection cooling, to minimize overheating. Purchase the best quality RCA cables you can afford, for reliability and less engine noise interference in the audio system. It is highly recommended that the amplifier be mounte

Descargado: 21   Tamaño del archivo: 2 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

This feature provides impact to your bass, but if not adjusted correctly, it can be over used and cause damage to your speakers and amplifiers. It is best to slowly turn this setting clockwise until the desired punch is felt. It is not recommended to exceed the 12 o’clock position unless listening at a low volume or a low recording quality as this can result in high distortion and possibly clipping. Low Pass: The Low Pass control acts as a ceiling and doesn’t allow frequencies to the right of th

Descargado: 8   Tamaño del archivo: 2 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

The next step is to scrape the paint off the vehicle chassis , slightly larger than the ground lug, at the connection point. Drill a clearance hole in the chassis, the same size as the lug hole, and use a bolt, spring washer and nut to securely fasten the ground lug. Use petroleum jelly to coat the bolt/lug connection, to prevent oxidization with time. TIP: Use the same approach when installing head units, equalizers or any audio equipment for that matter - run short individual grounds from each

Descargado: 2   Tamaño del archivo: 2 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

Hiss, or white noise 1 - High levels of white noise usually occurs when amplifier level controls are turned up too high - readjust according to the procedures in section ”Setting up systems after installation for best performance” 2 - Another major problem that can cause excessive hiss, is a noisy head unit - unplug the amplifier input RCA cables, and if the hiss level reduces, the source unit is at fault. Electrical interference The inside of an automobile is a very hostile electrical environme

Descargado: 65   Tamaño del archivo: 3 mb   Fabricar: MB QUART  
Categoría: Avtousiliteli
@name

Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. Lower power amplifiers will clip earlier than their more powerful cousins, and cause loudspeaker failure when overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils. Amplifiers should be mounted with the fins running horizontally for best convection cool





Categoría