example of a through mount setup. another option for mounting is a "direct Mount" where the machine is simply secured to the workbench with a lag screw. .................................................................................. Figure 9.. example of a direct mount setup. Creating Bends 1.. lift the clamp cam shaft to release the clamp die. Rotate the clamp die as necessary to accommodate the thickness of your work- piece, then slide the clamp cam shaft back into the base (Figures 10 & 11

2. Ensure the cup is securely tightened and all other fittings are secure to avoid air leaks or material spills. 3. set the inlet air pressure (the air coming to the spray gun) to the lowest pressure recommended in tool data on page 7 or to the material manufacturer's recommendations. 4. adjust the atomizing cap to vertical or horizontal. see atomizing cap and fan adjustments on page 12 for further explanation. 5. Fill the cup with material. 6. trial and error are necessary to achieve the result

MAINTENANCE • The Model G9017 and G9018 are basically maintenance free. However, the oil level should be kept constant at about 2.5 pints of quality hydraulic oil. • Too much oil will force the surplus oil to leak from the bottle jack fill plug (Figure 8), causing a mess. • Not enough oil will cause loss of power. To add oil: 1. Set the tube bender upright, retract the piston rod fully and remove the fill plug (Figure 8). Fill Plug Figure 8.Fill Plug. 2. Fill the bottle jack to the level of the

2 22. ..Make sure the Stop (2) is loose. 3 33. ..Move the Vise Assembly (5-9 & 15) to the rear position on the arm of the Mounting Plate. 4 44. ..Screw the Round Die Mounting Shaft (28) into the Mounting Plate. 5 55. Set the Round Die (29) onto the Mounting Shaft. 6 66. Move the Bending Block Assembly (16, 17, 22-24) back all of the way. You may have to release the Bending Block Locking Plate (21) by loosening the two Hex Key Bolts (20). Do not secure the Locking Plate at this time. 7 77. ..Set

Add the reserved tomatoes, parsley, and walnuts, pulse to chop, 10 times. Add the vinegar, basil, rosemary, and black pepper, pulse to combine, 5 times. With the machine running, add the olive oil in a steady stream, about 30 seconds. Add the reserved cheese and pulse to combine, 5 times. Allow to rest for 30 minutes before using for the flavors to blend. Transfer to a glass jar with a plastic lid and refrigerate until ready to use. Keeps 2 weeks in the refrigerator. Nutritional information per

CAUTION: THE CUTTING TOOLS HAVE VERY SHARP EDGES. To avoid injury when unpacking the parts, please follow these instructions. 1. Place the box on a low table or on the floor next to the kitchen counter or table where you intend to keep the food processor. Be sure the box is right side up. 2. Remove the cardboard insert. You will see a rectangular block of plastic foam that holds the processor parts, each fitted into a cavity in the foam. 3. The Detachable Disc Stem for the discs (A) sits in a ca

fat 1g • chol. 106mg • sod. 701mg • fiber 5g Pizza Pizza Pesto, Cheese & Fresh Tomato Pizza Homemade pesto and fresh, ripe tomatoes make this a great summertime pizza. Makes one 14-inch pizza or two 9-inch pizzas, to serve 4 Pizza Dough, p. 27 1-1/2 ounces Italian fontina cheese, very well chilled 1/2 pound firm but ripe plum tomatoes 3 tablespoons pesto, p. 30 1/2 ounce Reggiano Parmesan, cut in 1/2-inch cubes 1 teaspoon extra virgin olive oil 2 ounces fresh mozzarella, very well Cornmeal for d

PG 1 INTRODUCTION.......................... PG 1 THE PARTS ................................. PG 2 ASSEMBLING THE PARTS......... PG 3 TIPS FOR PROCESSING............ PG 4 PROCESSING FOOD.................. PG 5 OPERATING TECHNIQUES......... PG 6 TROUBLESHOOTING ................. PG 7 CLEANING AND STORAGE......... PG 7 RECIPE SUGGESTIONS ............ PG 7 WARRANTY..................................PG 11 IMPORTANT SAFEGUARDS When using an electrical appliance, basic safety precautions should always b

Press the ON lever and drop the food pieces through the small feed tube while the machine is running. After adding a cupful this way, add the remaining food to the bowl and process in the usual way. To chop hard foods like garlic, hard cheese Remove the small pusher, press the ON lever and drop the food through the small feed tube while the machine is running. Small foods like garlic can be dropped in whole. Larger foods like hard cheese should be cut into 1-inch pieces. This method of processin

.. . .. . . . .. . .. .. . .. . . . .. . .. . . . .. .2 Features and Benefits .................................4 Before You Begin.. . .. .. . .. . . . .. . .. .. . .. . . . .. . .. . . . .. .5 Assembly ...........................................5 Operation . .. . . . .. . .. .. . .. . . . .. . .. .. . .. . . . .. . .. . . . .. .8 Charging & Battery Life ...............................10 Storage Stand / Wall Brackets. . . .. . .. .. . .. . . . .. . .. . . . ..11 Cleaning. . .. . . . .. . .. .. .