. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before you begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Plumbing and clearance requirements. . . .. . . .. . . . . . . . . . . . . . . . .4 Field wiring diagrams. . . . .

5. Icemaker related problem. 6. Faulty or disconnected wiring. 1. Check switch and replace if necessary. 2. Check switch and replace if necessary. 3. Replace bin thermostat. 4. Replace transformer. 5. Refer to Icemaker Operation and Service Manual for diagnosing. 6. Check for power and bin signal on icemaker PC board. 15 Symptom Carbonator pump not turning on. Carbonator pump is not turning off. Carbonation system is not carbonating. Carbonation system is producing excessively carbonated beverag

1. Power switch in OFF position or faulty. 2. Bin signal switches in OFF position or faulty. 3. Faulty bin thermostat. 4. Faulty transformer. 5. Icemaker related problem. 6. Faulty run capacitor. 1. Check switch and replace if necessary. 2. Check switch and replace if necessary. 3. Replace bin thermostat. 4. Replace transformer. 5. Refer to icemaker Operation and Service Manual for diagnosing. 6. Check for power and bin signal on icemaker PC board. If problems persist after following this basic

drains electrical conn. 6" min 17" (432 mm) 18.875" (479mm) 18.875" (479mm) ice transport tube 12" min counter top 32.375" (823mm) Side View 24.62" (626mm) 30" (762mm) 15" (381mm) 10" (254mm) 2" (51mm) ice waterbath (VU300B only) 8.5" (216mm) ice transport tube entry 27.5" (699mm) bin signal power 3/4" drain nipple 1/2" ID drain tube beverage lines 6 Dual-sided dispensers Required clearances 60" (1524mm) above counter for installation if dispenser will be dropped into counter 49" (1245mm) above

Allow the system to sit for approximately 20 minutes. During this period the system pressure should not rise. If the system pressure rises and stabilizes there is moisture in the system and further evacuation is needed. If the pressure continues to rise check the system for leaks. Ambients Minimum Maximum Air temperature1 10.C/50.F 37.8.C/100.F Water temperature2 4.4.C/40.F 32.2.C/90.F 1Ambient air temperature is measured at the air-cooled condenser coil inlet. 2Ambient water temperature is meas

Do not hang dispenser on flange. All dispensers must be installed level in both directions to ensure proper operation. 1. Check that dispenser location meets all requirements in this manual and cut counter as shown. Plan View Plan View units with up to 8 valves units with 10 valves counter cut-out counter cut-out Front of counter +.125" - .125"30.375" (772mm) +3 mm - 3 mm 26.25" +.125" - .125" (667mm) +3 mm - 3 mm 26.25" Front of counter +.125" - .125" +.125" - .125" 36.375" (924mm) +3 mm - 3 mm

11 Recommended daily dispenser cleaning 1. Remove all debris from drain pan. 2. Pour 1 gallon (4L) hot water into drain pan to keep drain lines clear. Recommended weekly dispenser cleaning 1. Remove drain pan and grille and wash with Solution A. Rinse thoroughly. 2. Remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning Solution A, rinse, sanitize with Solution B and reinstall. 3. Pour a solution of one cup (8oz/237ml) household bleach mixed with one gallon (3.8L) hot

Crushed, flake, bagged, nugget or congealed ice cannot be used. Use of these ices can jam dispenser and void warranty. Separate any “waffle-like” sections of cubes before adding to dispenser. For ice compatibility questions, please call Follett customer service at (800) 523-9361 or (888) 2-FOLLETT or (610) 252-7301. 4 Specifications Electrical Each icemaker and dispenser require a separate circuit with with electrical disconnect within 10 ft (6m). Equipment ground required. Standard electrical –

Apply a thick bead, approximately. 1/4" (6mm) diameter, of NSF listed silicone sealant (Dow- Corning RTV-732 or equivalent) 1/4" (6mm) inside marked outline of dispenser. 11. Carefully position dispenser on counter. 12. Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter. (Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet fitting while pulling on tubing.) 13. Secure dispenser to counter wit

Install supplied insulation to run of transport tube required for your site, leaving approximately 51mm (2") of tube exposed at free end. 8. Check that insulated tube runs continuously from icemaker to dispenser with no dips. All units 9. Slip supplied hose clamp onto tube and push tube onto exit port of evaporator. ! Only use tubing supplied by Follett Corporation. Do not twist hose when securing evaporator. 10. Fasten tube on port with hose clamp, being sure that clamp is positioned on evapora