17 localizados en la base de la taladradora. Fig. 17 DE FUNCIONAMIENTO CONTROLES Y AJUSTES INTERRUPTOR El interruptor (A) Fig. 18 esta localizado en la parte delantera del cabezal de la taladradora. Para ENCENDER la taladradora, mueva el interruptor a la posicion elevada. Para APAGAR la taladradora, mueva el interruptor a la posicion inferior. A A Fig. 18 27 BLOQUEANDO EL INTERRUPTOR EN LA POSICION DE APAGADO IMPORTANTE: Cuando la herramienta no es adentro uso, el interruptor se debe bloquear en
12. MANTENGA las manos y los dedos alejados de labroca taladradora o la herramienta de corte. 13. NO INTENTE taladrar material que no tenga una superficie plana contra la mesa. FIJE CON ABRAZADERAS LA PIEZA DE TRABAJO o sujetelacontra la columna para impedir que gire. Ademas, sujete con abrazaderas la pieza de trabajo cuandoutilice una sierra perforadora o una herramienta decorte de mas de 1/2 pulgada de diametro. 14. DETENGA la taladradora siempre antes de quitar laspiezas descartadas de la mes
#ts10556 printed in taiWan .........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
Algunos ejemplos de esas substancias químicas son: • plomo de pinturas a base de plomo, • sílice cristalizado de ladrillos y cemento y otros productos de albañilería, y • arsénico y cromo de la madera químicamente tratada (CCA). El riesgo al contacto con estas substancias varía, según la frecuencia en que se haga este tipo de trabajo. Para reducir la exposición a esas substancias químicas: trabaje en un área bien ventilada, y trabaje con equipos de seguridad aprobados, tales como máscaras co
#TR8234 PRINTED IN CHINA. ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
Oil Bottle..................................................... 1 D. T-Nuts......................................................... 2 E. Chuck Key .................................................. 1 F. End Wrenches 8/10, 14/17, 17/19mm .... 1 ea G. Spindle Spanner Wrench ........................... 1 H. Hex Wrench Set 3, 4, 5, & 6mm ........... 1 ea I. Drawbar Hex Wrench ................................. 1 A B Figure 3. G0619 out of the crate. E H F I C G D Figure 4. Inventory. In the event th
The batteries can explode in a fire. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin - a.Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention
3. Carefully lay the column/base on its side. 4. Slide the column all the way into the bottom of the headstock (approximately 4"-6"). base in the fully upright position. If the base starts to slide when tilting, you MUST have a third person hold the base from sliding to avoid personal injury or machine damage. Figure 12. Tilting drill press upright. -20 G7947/G7948 12 Speed Floor Drill Press 6. Suspend a plum bob from the center of the headstock spindle so it is over the tape/ruler as shown in F
Put on heavy leather gloves to protect your the side of the head stock so the cover stays hands from possible lacerations if the spring splined with the locking lug; loosen the jam uncoils during the next step. nut and loosen the cover nut approximately 1.4" (see Figure 43). 5. Pull the cover outward just enough to disengage the spring-cover lock slot from the locking lug. Note: It is important to keep a good grip during this step. Letting go of the cover will cause the spring to rapidly uncoil.
....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................