Cuando gire la perilla a COOLER (mas frio) (azul), el aire interior se enfriara. Si gira la perilla a WARMER (mas calido) (rojo), el aire interior subira de temperatura. Solo la serie 3800 Cuando la temperatura externa es menor a 20° F, el calefactor electrico del acondicionador de aire comienza a emanar calor, reemplazando a la bomba de calor. Control de modos HIGH COOL (Frio alto) y LOW COOL (Frio bajo) proporcionan frio mediante diferentes velocidades de ventilador. HIGH HEAT (Calor alto) y L

Asegurese de elegir el cable correcto para su instalacion. Kit de suministro de energia Clasificacion de circuito derivado y amperaje Cable de energia GE de la unidad con dispositivo LCDI 15 RAK3153 20 RAK3203 30 RAK3303* *No se ha aprobado el uso en modelos de 7000 BTU. Los cables de alimentacion pueden incluir un dispositivo para interrupcion de arco o uno para interrupcion y deteccion de fuga de corriente. Se incluye un boton de prueba y de reinicio en el dispositivo. El dispositivo debe pone

2 Connect to electrical power. 3 See the special instructions below for applicable supply voltages. 4 Reinstall the room cabinet. Branch Circuit and Proper GE Unit Amperage Rating Subbase Kit 15/20 RAK204D20 30 RAK204D30 230/208 VOLT ELECTRICAL SUPPLY All wiring, including installation of the receptacle, must be in accordance with the NEC and local codes, ordinances and regulations. This unit is equipped with a line cord for appropriate amperage wall receptacle. See below. Electrical subbases pr

For service in Canada, call 1.800.361.3400. Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. For The Period Of: GE Will Replace: One Year From the date of the original purchase Any part of the Zoneline which fails due to a defect in materials or workmanship. During this full one-year warranty, GE will also provide, free of charge, all labor and on-site service to replace the defective part. Five Years From the date of the original purc

Quick Reference 2500 Series Cooling with Electric Heat MODEL NUMBER COOLING (Btuh) Cooling Watts EER Electric Heat (Btuh) Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) AZ25E07D2* 7100/6900 600/585 11.8/11.8 8600/7100 2550/2090 11.0/10.0 15 AZ25E07D3* 7100/6900 600/585 11.8/11.8 11700/9600 3450/2820 15.0/13.6 20 AZ25E09D2* 9000/8800 785/765 11.5/11.5 8600/7100 2550/2090 11.0/10.0 15 AZ25E09D3* 9000/8800 785/765 11.5/11.5 11700/9600 3450/2820 15.0/13.6 20 AZ25E09D5* 9000/

• Includes 3-meter conductor wire for hook-up to Vertical Zoneline. • Required for Motion Sensor/Door Switch applications. * A-B Series: Zonelines® built before 1987 – Zoneline I, II, III, and IV; AZC Series: Zonelines built from 1987 to 1992 – includes AZR Series – Zoneline 1000, 2000, 2500, 2700, 3000, 4000, 5000; AZ Series: Zonelines built after 1992 – Zoneline 2100, 3100, 2600, 5100 / Zoneline 2200, 3200, 5200 / Zoneline 2500, 3500, 5500 / Zoneline 2800, 3800, 5800. RAVWP6 (AZ Series*—7500)

Branch Circuit and Proper GE Unit Amperage Rating Subbase Kit 15 RAK204D15P 20 RAK204D20P 30 RAK204D30P* 14 Installation Instructions 265 VOLT ELECTRICAL SUPPLY JUNCTION BOX Remove the junction box cover by taking out the Remove the junction box by taking out the top rear . Note how the tab on the lower right corner ves to hold the side in place. This will help when the box is being reinstalled. The cord will be coiled up inside the junction box. 1 Unit connector Junction box cover Junction box

Secure the case through the case track into the window stool on each side, using two 1. screws. Secure to stool 6 Assemble and Attach the Sill and Support Brackets Attach both sill brackets to the window sill using a 1. long screw on each side. Tighten the bolts and nuts on both sides. Loosely attach the sill brackets to the support brackets with 5/8. long carriage bolts and nuts. Find the track hole that aligns with the sill bracket on the outer edge of the window sill. Using the 5/8. long mach

21 Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support Through-the-wall installation. Read these instructions completely and carefully. Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions 1 Preparation of the Opening in the Wall Make certain a wall receptacle is available close to the hole location or make arrangements to install a receptacle. The cord

. . . . . . . . .2 Operating Instructions Controls—Dip Switches . . . . . .3–5 Controls—Terminal Connections . . . . . . . . . . . . . .6, 7 On/Off Switch . . . . . . . . . . . . . . .8 Ventilation Control . . . . . . . . . . .8 Care and Cleaning Air Filters . . . . . . . . . . . . . . . . . . .9 Base Pan . . . . . . . . . . . . . . . . . . .9 Exhaust Coils . . . . . . . . . . . . . . . .9 Installation Instructions Electrical Supply . . . . . . . . .11–13 Installing the Zoneline . . . .14–21 Pre