The thatch can soon be so dense as to prevent water, nutrients and oxygen penetrating the lawn’s root system, resistance to wear and new growth subsequently weaken. Disease and drought resistance is reduced with weeds and moss becoming dominant. Scarification not only removes harmful thatch, it also reduces the amount of moss and weeds. In addition the compacted soil surface is loosened thus enabling it to breathe and absorb water, oxygen and nutrients. Due to the thinning out achieved by scar

8. Para parar el motor, suelte el control de aceleracion y mueva el interruptor de ENCENDIDO / APAGADO a la posicion APAGADO. 9. Si el motor se ahoga, saque la bujia y sequela. Consulte “Mantenimiento de la bujia” en la seccion de Mantenimiento de este manual. Luego, jale la cuerda de arranque teniendo la palanca del cebador en la posicion Cebador apagado. ADVERTENCIA: El silenciador y las areas que lo rodean se calientan mucho luego de arrancar el motor. No toque estas areas. Filtro de aire Int

Other states may have similar laws. Federal laws apply on federal lands. See an Authorized Service Center for a spark arrester for the muffler. F–031305L 9 OPERATION KNOW YOUR CULTIVATOR READ THE OWNER’S MANUAL AND ALL SAFETY RULES BEFORE YOU OPERATE the cultivator. To familiarize yourself with the location of the controls, compare the illustrations with your cultivator. Save this manual for future reference. Throttle Control – Controls the engine speed and the tine rotation. The cultivator is e

Remove the air filter cover and the air filter. 3. Wipe the cover and the inside of the air filter housing with a clean cloth. 4. Clean the air filter in a solution of water and household detergent. Rinse thoroughtly in clean water. 5. Wrap the air filter in a dry clean cloth. Squeeze out (do not twist) all solution until dry. 6. Cover the outside of the air filter with oil. Use the same type of oil as used to make the fuel mixture. Lightly squeeze the air filter to distribute and remove any exc

NO. 1690715 10" Plow with Coulter Blade 5 Shank Cultivator 8 Blade 11" Disc Harrow FORM - 1669913 PRINTED IN U.S.A. 8110 Contents SAFETY RULES .................................................... ASSEMBLY ................................ ........................... .............................. Plow ............................................................ .......:'.... Cultivator ..................................................................... Disc Harrow ....... .............

Lay all the loose parts in carton out on floor or work bench. , Separate all of the hardware (nuts and bolts) into groups. Preassemble eleven clamps {Ref. 10) and hex bolts 1/2" x 1.50" long (Ref. 4). Thread bolts into clamps until one thread shows through weld nut. Preassemble two wheels (Ref. 11), wheel rods (Ref. 14), shoulder bolts (Ref. 12) and hex lock \ nuts (Ref, 13). Place shoulder bolt through wheel and thread into wheel rod. Secure shoulder bolt with hex lock nut. Model No. 193-98

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E13 Limpieza y almacenamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E17 Solucion de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E18 Especificaciones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E19 Garantia . . . . . . . . . . . . . . . . . . . . . . . . .

S Hold the unit firmly with both hands. S Keep firm footing and balance. Do not overreach or stand on unstable surfaces. S Look behind and use care when backing up. S Keep all parts of your body away from the tines and muffler. S Do not force the unit. Use only for jobs explained in this manual. Use only for cultivating. Do not abuse unit. Do not use in rain or wet locations. S Use only in daylight or good artificial light. TRANSPORTING AND STORAGE S Stop powerhead before leaving work area. S Al

No. 209 Mfr's. No.209 Mfr's. No. 203 PACKING The cultivator is packed in one carton disassembled for ease of shipment. ASSEMBLY 1. Attach parallel bars to dravr bar assembly as shown at (1). Lock with Jam nuts so bars are free to swing. 2. Attach depth crank (2) as illusiratod. Adjusting nuts (3) should be equally spaced on threads, 3. Clamp wheel standards to draw bar assembly as shown at (4). 4. Clamp lool holders to tool bar as shown at (5). 5. Attach the lool standards lo the tool