1087755 DATED 8-1-73 50-802 STAND FOR 34-570 9 HOMECRAFT SAW INSTALLATION 1- Remove stand from carton, 2.“' Assemble one short top brace (A) and one long bottom brace (B) ter panel (C), as shown in Fig. 1, using the eight carriage, bolts, flat washers, lockwashers and hex -nuts supplied. - The bottom of the panel (C) can be determined 'by the holes (D) for the: Accessory 50-118 Retractable Caster Attachment* IMPORTANT: 'The top brace (A) must be assembled to the panel (C) with the lip' (E) o

REVISE LA PIEZAS DA ADAS. Antes de proseguir con el uso estado. de la herramienta, un resguardo u otra pieza que este danada debe ser revisada cuidadosamente para asegurar que funcionara 3. SIEMPRE USE PROTECCION OCULAR. Utilice gafas de correctamente y realizara su funcion propuesta–revise el seguridad (deben cumplir con ANSI Z87.1). Las gafas comunes solo alineamiento de las piezas movibles, las ataduras de las piezas tienen lentes resistentes al impacto; no son gafas de seguridad. movibles, e

Place a 1/4" flat washer onto a 1/4-20x1/2" hex head screw and insert screw through hole in pulley guard and thread screw into the tapped hole in the casting. Repeat this process for the remaining hole. Raise the motor and assemble the belt (D) Fig. 7, to the desired steps of the two pulleys then release the motor. A speed selection chart (E) is located on the inside of the guard cover. When the belt is tensioned, tighten screws (C). FASTENING BAND SAW TO SUPPORTING SURFACE IF DURING OPERATION T

Al aprender la aplicacion, las limitaciones y los peligros especificos de la maquina, se minimizara enormemente la posibilidad de accidentes y lesiones. 2. USE PROTECCION DE LOS OJOS Y DE LA AUDICION. USE SIEMPRE ANTEOJOS DE SEGURIDAD. Los lentes de uso diario NO son anteojos de seguridad. USE EQUIPO DE SEGURIDAD CERTIFICADO. El equipo de proteccion de los ojos debe cumplir con las normas ANSI Z87.1. El equipo de proteccion de la audicion debe cumplir con las normas ANSI S3.19. 3. USE INDUMENTAR

12. Repita este proceso para los cinco agujeros restantes. 13. Monte el otro lado de la base de soporte de la misma manera. A B C Fig. 7 57 - Spanish 14. Alinee los agujeros de la base (A), Fig. 8, con los agujeros de los dos lados (B). 15. Introduzca un tornillo de cabeza hexagonal con pestana M8 x 1.25 x 16 a traves del agujero del lado de la base de soporte (B), Fig. 8, y a traves del agujero de la base (A). 16. Enrosque una tuerca hexagonal M8 x 1.25 en el tornillo. NOTA: Apriete libremente

For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols to the right. Please read the manual and pay attention to these sections. Indicates an imminently hazardous situation which, if no

2. Remove arbor nut (A) Fig. 29, and outside blade flange (B). NOTE: THE BLADE IS TO BE ASSEMBLED BETWEEN THE TWO BLADE FLANGES (B) AND (C) WITH THE RECESSED SIDES OF THE FLANGES AGAINST THE SAW BLADE. 3. Assemble the saw blade (D) Fig. 30, between the two blade flanges making sure the teeth of the saw blade are pointing down at the front. 4. Assemble arbor nut (A) Fig. 30 to shaft and tighten with wrench (E) Fig. 30, while keeping arbor shaft from turning with other wrench (F). C B A Fig. 29 D

(Fig. 3) J – BEVEL CLAMP LEVER. Controls tilt of motor for bevel cutting operations. Locks motor at any desired angle on the bevel scale. (Fig. 3) K – TABLE CLAMP KNOBS. Allows the operator to quickly set the desired fence position. (Fig. 3) L – ON-OFF SWITCH. Conveniently placed at eye level; switch can be turned on or off in an instant for added operator protection. (Fig. 3) M – MITER SCALE. Indicates degrees left and right for setting track arm. (Fig. 2) 6 ASSEMBLY ASSEMBLING STEEL LEGS TO BA

6. Loosen three screws (F) Fig. 52, and loosen track arm clamp handle (G). 7. To move front end of track arm to the right, loosen set screw (H) Fig. 53, and tighten set screw (J). To move front end of track arm to the left, loosen set screw (J) and tighten set screw (H). 8. When the cuttinghead travels parallel to the square, tighten three screws (F) Fig. 52. Replace miter scale (E) Fig. 51, and replace and tighten three screws (D). Make certain the zero graduation mark on the scale (E) lines up

NOTE: To mount the saw to the stand, use the four hex head screws, flat washers, external tooth lockwashers and hex nuts (items 8, 9, 10 and 11) of the parts 'drawing. IF DURING OPERATION THERE IS ANY TENDENCY. 'FOR THE TOOL TO TIP OVER, SLIDE OR'WALK ON SUPPORTING SURFACE, THE STAND OR BENCH MUST BE SECURED TO THE FLOOR. Fig. 2‘ Replacement Parts Ref. Part Description No. No. Cat. #50-802 Stand Ass’y. Consisting of: 1 1087508 Front and Rear Panel* 2 1087507 Bottom Brace 3 1087509 Top