Loosen and remove the blade cover locking knobs (10). 3. Remove the blade cover (9). 4. Take the 2 face spanners and use 1 to hold the blade securing nut and the other to hold the flat part of the spindle. Turn the spanner holding the blade securing nut in an anti-clockwise direction to loosen the nut. 5. Remove the nut, outer blade flange and blade. 6. Wipe a drop of oil onto the inner blade flange and the outer blade flange where they contact the blade. 7. Fit the new blade onto the spindle ta

General safety instructions 4 This product is warranted for a 2-year period for home Additional safety rules for band saws Unpacking Know your product Components Assembly 5 6 6 8 8 domestic use from the date of the original purchase. If found to be defective in materials or workmanship, the tool or the offending faulty component will be repaired or replaced free of charge with another of the same item. A small freight charge may apply. Proof of purchase is essential. We reserve the right to reje

Upper blade guide assembly 17. Upper guide assembly lock knob 18. Dust extraction port (not shown) 19. Upper blade guide 20. Upper blade support head (not shown) 21. Lower blade support head (inside wheel housing) 22. Table 23. Lamp 24. Protractor 7 5 2 6 3 23 11 16 17 19 22 12 13 14 4 21 24 8 9 1 10 Setting up Electrical installation WARNING. The band saw is equipped with a 230 – 240V ~ single phase 200W motor. It must be connected to an earthed socket and it is recommended that a residual curr

You will require a 13mm wrench or adjustable wrench (not supplied) for the lock nut (Fig. V) and the 6mm hex key for the set screws (Fig. W). Setting the fence square with the table 1. Make sure that the electrical plug is removed from the power point. 2. Push the saw arm (5) down to its lowest position and engage the release knob (6) to hold the saw arm in the transport position. 3. Loosen the mitre lock (25). 4. Rotate the table (21) until the pointer is positioned at 0.. 5. Tighten the mitre

Children and infirm people must not use this tool. Children should be supervised at all times if they are in the area in which the tool is being used. It is also imperative that you observe the accident prevention regulations in force in your area. The same applies for general rules of occupational health and safety. WARNING. When using power tools, basic safety precautions should always be taken to reduce the risk of fire, electric shock and personal injury. Also, please read and heed the advic

Disc guard 4. Front spark shield 5. Spark shield locking knob 6. Cut off disc 7. Spindle lock 8. Rear spark shield 9. Base 10. Rubber foot 11. Vice lock release lever 12. Vice handle 13. Vice 14. Fence 15. Carry handle 16. Lock down knob 17. Depth stop 18. 8mm Hex key 19. 5mm Hex key 1 18 19 3 16 2 15 4 5 7 6 17 8 14 13 9 11 16 12 10 Overview The cut off saw is used for cutting steel such as pipe, box section, rectangular, angle iron and steel bars. The saw can cut at angles from 0° to 45° left

4. Tighten the bevel adjustment knob (6) to secure the base plate. Note. Always make a trial cut in a scrap piece of material along a guideline to determine how much you should offset the blade from the guideline to make an accurate cut. Switching on and off 1. Connect the plug to the power supply. 2. Depress the lock-off button (2) and squeeze the trigger switch (1). 3. The blade will take approximately 2 seconds to reach full speed. Note. When you release the trigger, the machine turns off and

Lleve proteccion auditiva. Lleve proteccion ocular. Lleve proteccion respiratoria. Doble aislamiento para proteccion adicional. Conforme a las normas de seguridad y a la legislacion correspondientes. Declaracion “CE” de Conformidad El abajo firmante: Mr Philip Ellis Autorizad por: GMC Declare that: Tipo y No Serie: DB250SMS/DB305SMS Modelo/Nombre: Sierra Para Cortar Ingletes Compuestos Deslizante de Bisel Doble Energia electrica: 230-240V~ 50Hz 1800W Se halla en conformidad con la Directiva: • D

• Observe la direccion de giro del motor y la hoja. • No bloquee la proteccion extraible en la posicion abierta y asegurese siempre de que este funcionando debidamente, girando libremente y volviendo para cubrir completamente los dientes de la hoja. • Conecte la sierra a un dispositivo de recogida de polvo y asegurese de que se haga funcionar debidamente. Como operador de la sierra, asegurese de comprender los factores que tienen influencia en la exposicion al polvo, incluyendo el tipo de materi