Saw blade change ADanger! Risk of injury by the saw blade’s teeth. Wear gloves when changing blades. 1. Remove the two fastening screws of the removable table section. 2. Lift removable table section up and remove. 3. Raise blade fully. 4. Take blade guard off. 5. Lift chip case cover slightly and swing to the side. The cover is hooked into the bottom of the chip case and can not fall down. 25 20 15 10 5 0 30 35 2.10 PK 255 6. To block the saw blade insert lock bar into hole in the saw table and
. . . . . . . . . . . . . . . . .3 Table Extension . . . . . . . . . . . . . . . . . . . . . .5 Rallonge laterale de table . . . . . . . . . . . . . .7 Tafelverbreding . . . . . . . . . . . . . . . . . . . . . .9 Allargamento del tavolo . . . . . . . . . . . . . . .11 Extension de la mesa . . . . . . . . . . . . . . . .13 Alargador da bancada . . . . . . . . . . . . . . . .15 Bordforbredelse . . . . . . . . . . . . . . . . . . . . .17 Bordforlengelse . . . . . . . . . . . . . . . . . . . . .19 T
. . . . . . . . . . . . . . . . . . .3 Operating Instruction . . . . . . . . . . . . . . . . .12 Instructions d’utilisation . . . . . . . . . . . . . . .21 Manuale d’istruzioni . . . . . . . . . . . . . . . . . .31 Manual de uso . . . . . . . . . . . . . . . . . . . . . .41 A0002IVZ.fm D DEUTSCH ENG ENGLISH KONFORMITATSERKLARUNG DECLARATION OF CONFORMITY Wir erklaren in alleiniger Verantwortlichkeit, da. dieses Produkt mit We herewith declare in our sole repsonsibility that this product den folg
Max. saw blade O 250 mm Saw blade arbor bore O 30 mm Max. blade speed 4000 min-1 Max. depth of cut 80 mm Safety devices Riving knife The riving knife prevents the workpiece from being caught by the rising teeth of the saw blade and being thrown against the operator. Always have riving knife installed during operation. Blade guard The blade guard protects against accidental contact with the blade and keeps chips from flying about. Always have blade guard installed during operation. Push stick The
80 0 ... 53 0 ... 80 0 ... 53 Dimensions length saw table width saw table height (with blade guard) mm mm mm 760 665 850 760 665 850 Weight approx. kg 68 68 No-load noise emission values, dust collection off Sound pressure level A LpA Sound power level A LWA dB (A) dB (A) 77.0 87.0 77.0 87.0 Noise emission value during sawing operation, dust collection on Sound pressure level ALpA Sound power level A LWA dB (A) dB (A) 87.0 98.0 87.0 98.0 Available saw blades Application Description Stock-no. Saw
Problemas y averias .................61 15. Especificaciones tecnicas........62 2. .Lea esto en primer lugar! Este manual de instrucciones se ha realizado para ensenarle, en calidad de usuario, como manejar este equipo y trabajar de forma segura con el mismo. Este manual debera utilizarse segun sigue: Antes de poner en servicio el equipo, lea todo el manual de instrucciones. Al leer este manual de instrucciones preste especial atencion a las instrucciones de seguridad; procure cumplir siempre to
The gap between riving knife and blade must not exceed 10mm/3/8 “. Do not set top of riving knife lower than 2mm-5/64” below the blade’s crown. 9.2 Blade Change Disconnect from power before servicing! Remove chip case lid and loosen arbor bolt. Remove arbor bolt and counter flange, then take off blade. Note: Arbor bolt has L.H. thread, turn clockwise to loosen. Before installing new blade clean blade seat and apply a light coat of oil to the arbor bolt. - Be sure that teeth are pointing in
1. Remove table insert (80) from saw table (push up from underneath). 2. Fit new table insert. 9.7 Saw Cleaning 1. Open the lower housing door. 2. Remove the chip case (81) and empty it. 3. Remove chips and saw dust with brush or vacuum from: . inside of the lower band saw housing; . blade guides; . operating elements 4. Swing door catch lever (82) up and put the chip case back in. 9.8 Saw storage ADanger! Store saw so that . it can not be started by unauthorized persons and . nobody can get hur