Consejos y trucos.....................63 10. Conservacion y mantenimiento ..........................63 10.1 Cambio de la hoja de sierra........63 10.2 Limpieza del mecanismo de reglaje de la altura de la hoja de la sierra .................63 10.3 Almacenamiento de la maquina.............................64 10.4 Mantenimiento............................64 11. Reparacion................................64 12. Transporte.................................64 13. Accesorios suministrables..6467 14. Prote

Reparacion................................60 11. Transporte.................................60 12. Accesorios suministrables......60 13. Proteccion ecologica................60 14. Problemas y averias.................60 15. Especificaciones tecnicas.......61 16. Accesorios suministrables......63 2. .Leer esto en primer lugar! • Monte este aparato siguiendo estrictamente estas instrucciones. La sierra cumplira las normas de seguridad y proporcionara un manejo fiable unicamente si se respetan exact

1001 % a r jmSmSBmSSSmm •tv’*,.' vi/.’. ' ■- i 1 8k * V. 04/92 - EB-D - GB Stock-no. 115 107 8059 Contents 1.0 Scope of Application 2.0 Specifications 3.0 User Responsibility 4.0 Standard Accessories 5.0 Optional Accessories 6.0 Assembly 7.0 Mitre Fence Assembly 8.0 Installation 9.0 Operation/Settings 10.0 Cutting 11.0 Saw Dust Collection (optional accessory) 12.0 Crane Lifting 13.0 Safety Rules 14.0 Care and Maintenance 15.0 Wiring Diagrams 16.0 Spare Parts List and D

The gap between riving knife and blade must not exceed 10mm/3/8 “. Do not set top of riving knife lower than 2mm-5/64” below the blade’s crown. 9.2 Blade Change Disconnect from power before servicing! Remove chip case lid and loosen arbor bolt. Remove arbor bolt and counter flange, then take off blade. Note: Arbor bolt has L.H. thread, turn clockwise to loosen. Before installing new blade clean blade seat and apply a light coat of oil to the arbor bolt. - Be sure that teeth are pointing in

-Crosscuts should be performed only with the help of a mitre fence or the Sliding Carriage PK, available as optional accessory. -Do not crosscut round stock, for ripping use the Square and Round Stock Jig available as optional accessory. -Maximum saw blade diameter is 300 mm, the minimum blade diameter must be 250 mm. User Responsibility This machine will perform in conformity with the description contained tin the instructions provided. This machine must be checked periodically. Defective equip

Problemas y averias .................61 15. Especificaciones tecnicas........62 2. .Lea esto en primer lugar! Este manual de instrucciones se ha realizado para ensenarle, en calidad de usuario, como manejar este equipo y trabajar de forma segura con el mismo. Este manual debera utilizarse segun sigue: Antes de poner en servicio el equipo, lea todo el manual de instrucciones. Al leer este manual de instrucciones preste especial atencion a las instrucciones de seguridad; procure cumplir siempre to

• Let tool run idle for a short time only. 4. Operation 4.1 Before initial operation • Install swivel-type air inlet. • Fit the plug nipple. 4.2 Using the tool A Caution! To ensure a long service life of this tool, it needs to be supplied with sufficient quantities of pneumatic oil. This can be achieved by: . a service unit with oiler at the compressor. . a lubricator, installed in the air line or directly on the air tool. ENGLISH . adding approx. 3-5 drops of pneumatic oil by hand every 15 minu

. . . . . . . . . . . . . . . 3 A0250IVZ.fm 2 3 ENGLISH 1. Scope of delivery 1 3 2 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 16 22 23 24 26 25 27 28 29 30 31 32 1 Table insert 2 Riving knife 3 Blade guard 4 Saw blade 5 Suction hose 6 Handle for push block 7 Push stick / feeding aid 8 Hose carrier 9 Rip fence extrusion / rip fence 10 Rip fence 11 Table top 12 Guide extrusion / rip fence 13 Guide bar / mitre fence 14 Stanchion, short (2x) 15 Stanchion, long (2x) 16 Leg (4x) 17 Handwheel / blade

. . . . . . . . . . . . . . . . . . .3 Operating Instruction . . . . . . . . . . . . . . . . .12 Instructions d’utilisation . . . . . . . . . . . . . . .21 Manuale d’istruzioni . . . . . . . . . . . . . . . . . .31 Manual de uso . . . . . . . . . . . . . . . . . . . . . .41 A0002IVZ.fm D DEUTSCH ENG ENGLISH KONFORMITATSERKLARUNG DECLARATION OF CONFORMITY Wir erklaren in alleiniger Verantwortlichkeit, da. dieses Produkt mit We herewith declare in our sole repsonsibility that this product den folg

To adjust, loosen the set screws located on the lower blade guide mounting block and slide blade guide arm back or forward to adjust properly (Fig.17). NOTE: Blade guides and blade tension should be checked and adjusted if needed after 3 hours of use. Frequent replacement of blade guides is recommended to maintain cutting accuracy and extend blade life. When pushing the material through the blade while cutting, make sure the round support bearing behind the blade does not spin. If the roller beg