1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Tel. 913/397.8200 or 800/800.1020 Fax 913/397.8282 GARMIN (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ, U.K. Tel. 44/1794.519944 Fax 44/1794.519222 GARMIN Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax 886/2.2642.9099 Website Address: All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, dissem

Important Codes: 1200. The VFR code for any altitude in the US (Refer to ICAO standards elsewhere) 7000. The VFR code commonly used in Europe (Refer to ICAO standards) 7500. Hijack code (Aircraft is subject to unlawful interference) 7600. Loss of communications 7700. Emergency 7777. Military interceptor operations (Never squawk this code) 0000. Military use Avoid selecting codes 0000, 7500, and all codes in the 7600-7777 range. These codes trigger special indicators in automated facilities. An a

The numbers 8 and 9 are not used for code entry, only for entering a Count Down time and for adjusting contrast and display brightness. Keys for Other GTX 327 Functions IDENT. Pressing the IDENT key activates the Special Position Identification (SPI) Pulse for 18 seconds, identifying your transponder return from others on the air traffic controller’s screen. The word IDENT will appear in the upper left corner of the display during this time. VFR. Sets the transponder code to the pre-programmed V

Contrast is controlled by the 8 and 9 keys. DISPLAY: This page is only displayed if manual backlighting mode is selected during installation configuration. Backlighting is controlled by the 8 and 9 keys. ADS-B: This page is displayed if the ADS-B pilot set option is selected during installation configuration of an ES enabled GTX 330. ADS-B defaults to ON at each power cycle. ADS-B ON/OFF is controlled by the START/ STOP key. Turn ADS-B OFF only at the request of ATC. Altitude Trend Indicator Whe

Garmin hereby grants permission to download a single copy of this manual and of any revision to this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual or revision must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. This

The deckmount light and standby LED on the hand held will both blink, the autopilot system is in a start-up mode and no operations are available for 30 seconds. How to engage Autopilot: When the STBY LED turns solid press the bull’s eye and release to engage the autopilot. When the AUTO LED is solid the autopilot is engaged. Press and hold the left straight arrow button to make a port turn, AUTO LED will start blinking, to stop turn release button, AUTO LED will revert to solid when a new headin

Heben Sie die rote Klappe an, und drucken Sie kurz die NOTRUF-Taste. 2. Wahlen Sie mithilfe des Kanal-Knopfes die Art des Notrufs aus. 3. Drucken Sie mindestens drei Sekunden lang die NOTRUF- Taste. Scannen nach Prioritatskanalen 1. Drucken Sie die 16/9-Taste (nordamerikanische Modelle) oder die 16+-Taste (internationale Modelle), um auf Kanal 16 umzuschalten. 2. Drucken Sie erneut die 16/9-Taste oder die 16+-Taste, um auf den Kanal mit der zweithochsten Prioritat umzuschalten. 3. Drucken Sie di

The scanner is automatically powered on with the MFD. The Welcome Page appears showing the GMR 21 or GMR 41 as a detected network connection. 2. Press ENTER when I Agree turns yellow, then press PAGE until the Radar Page appears. 3. During Standby mode, a countdown appears on the Radar Page and the status bar as the scanner prepares to operate. 4. With the scanner Ready, press and hold the FCTN key until Do you want to begin radar transmission? appears. 5. When safe (personnel are clear of the r

To complete the installation, you need the appropriate fasteners, tools, and mounts. These items should be available at most marine dealers. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check first to see what is on the other side of the surface. If you experience difficulty with the installation, contact Garmin Product support or seek the assistance of a professional installer. Installation Guidelines In order t

1. To customize system options on the GMI 10, from the instrument screen, select Menu > Setup > System. 2. For the listed options, select the appropriate settings or enter the necessary values. For example, you can select units of measure, language, enter total fuel capacity, and so on. To set the reference used to calculate heading information: 1. From the instrument screen, select Menu > Setup > System > Heading. 2. Choose from the following options: • Auto Magnetic—Automatic Magnetic Variatio