Then, connect the AC power wall outlet. Using the player on batteries Insert four size D (R20) batteries (not supplied) into the battery compartment. Replace the batteries when the player stops operating. Replace all the batteries Specifications • Frequency range CFM-20: FM: 87.6 - 108 MHz AM: 530 - 1 710 kHz CFM-30TW: TV H (WEATHER): 7 - 13 ch TV L/FM: 2 - 6 ch/ 87.6 - 108 MHz AM: 530 - 1 710 kHz • Antennas FM/TV: Telescope antenna AM: Built-in ferrite bar • Recording system 2-track, mono • Fre

• La unidad realizara la reproduccion de forma normal durante un espacio de tiempo incluso despues de que el indicador BATT se atenue. No obstante, sustituya las pilas lo antes posible. En caso contrario, la grabacion posterior no se grabara correctamente. Duracion de las pilas (Horas aproximadas) (EIAJ*) Reproduccion Grabacion Pila alcalina Sony LR6 (SG) 11 11 Pila Sony R6P (SR) 3 3 * Valor medido por la norma de EIAJ (Electronic Industries Association of Japan) (con una cinta de cassette Sony

2 Connect the AC power adaptor (supplied to TCM- 454VK) to the DC IN 3V jack of the battery charger adaptor and to the wall outlet. The power indicator lights up. 3 Unplug the AC power adaptor from the wall outlet and from the battery charger adaptor after about eight hours. Notes •The power indicator lights in green as long as the AC power adaptor is plugged to the wall outlet and the DC IN 3V jack, even when the charging has not been done. •Use only the supplied or recommended AC power adaptor

Review the portion Press and hold 0 REW/REVIEW just recorded during recording. Release the button at the point to start playback. * PAUSE c will be also automatically released when p STOP is pressed (stop-pause-release function). To monitor the sound For TCM-473V: Connect stereo headphones (supplied) firmly to the 2 (headphones) jack. For TCM-455V/454VK/453V: Connect an earphone (not supplied) firmly to the EAR jack. Notes •Do not use a CrO2 (TYPE II) or metal (TYPE IV) tape, otherwise the sound

Hand strap (1) (attached to the unit) as ECM-T110 (not supplied). speaker. Tape speed is too fast or too slow in the AC power adaptor (1) (TCM-454VK) When using a plug-in-power system microphone, the 2 Adjust the tape playback speed. •If the unit has not been used for a long time, set it in the playback mode. Battery charger adaptor (1) (TCM-454VK) power to the microphone is supplied from this unit. Set SPEED CONTROL to: playback mode and warm it up for a few minutes m SPEED CONTROL is set at a

Internal format conversion function By installing an optional HKSR-5001, when the operation mode of this unit is 23.98PsF or 24PsF, a 59.94i or 60i mode HD SDI output (audio/VITC multiplex) is made available. Additionally, conversion in either direction between 1080.1920 and 720.1280, and conversion from 4:2:2 signal to 4:4:4 signal is possible, and with the additional installation of an HKSR-5003, conversion from a 4:4:4 signal to a 4:2:2 signal. Noiseless playback with DT heads When using the

As the unit may become hot during operation, always leave sufficient space above the unit for ventilation. If you are mounting the unit in a rack, leave 1U of space above it. Allow at least 10 cm (4 in) at the rear of the unit for ventilation. You should not place the unit on a piece of equipment generating heat, e.g. an amplifier, to avoid possible problems with overheating. Make sure that the unit is mounted in a level position for correct operation. Do not mount the unit in a rack tilted 5° o

2 Hold down RADIO BAND•AUTO PRESET until “AUTO” flashes in the display. 3 Press DISPLAY•ENT•MEMORY. The stations are stored in memory from the lower frequencies to the higher ones. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Tune in a station you want. 3 Hold down the number buttons that you want to preset the new station on for about 2 seconds. To select the preset number over 10, pre