Setup Connect to Water Supply Connect hose from water supply to the garden hose inlet on the pressure washer. • The supply hose should not be longer than 50 ft (15 m) in length. • Inside diameter of hose should measure at least a 3/4 in. (19 mm). ti5420ati5422a Up to 100 ft (30 m) of 3/8 in. high-pressure hose may be used. Longer hoses could affect pressure washer and chemical injector performance balance. Installing Spray Tip Install spray tip on wand. (Installing and Changing Spray Tips, page.

Check fuel line and carburetor. Low oil Add oil to proper level. Engine ON/OFF switch in OFF position Turn switch to ON position. Water in fuel or old fuel Drain fuel tank and carburetor. Use new fuel and make sure spark plug is dry. Engine flooded or improperly choked Open choke. Pull engine starter rope several times to clear out fuel. Make sure spark plug is dry. Dirty air cleaner filter Remove and clean filter. Spark plug dirty, wrong gap or wrong type Clean, adjust gap or replace spark plug

ENGINE, gasoline, GX270, 9 HP 1 ENGINE, gasoline, GX340, 11 HP 1 ENGINE, gasoline, 13 HP 1 PUMP, water, 3000, complete 1 PUMP, water, 3300, complete 1 PUMP, water, 3500, complete 1 KIT, frame, includes wheels, feet 1 19 20 21 22 23 25 26 27 Ref. No. 116411 801546 100132 101566 801504 801137 116477 244804† Part No. SPRING, compression SCREW, cap WASHER, flat NUT, lock FOOT, rubber KEY, square WASHER, nylon KIT, repair, unloader, preset, 3000 Description 2 2 2 2 2 1 2 1 Qty. 4 5 7 8 9 10 11 12 13

Be sure latch is pushed fully down or it will not prevent the gun from being triggered. • When using a sandblasting kit, refer the sandblaster kit instruction manual for detailed operating and cleaning information. 1. Check oil level of engine and pump. 2. Check fuel level. 3. Check oil level in pump. It should be half way up the sight glass, located on the front of the pump. Add pump oil as necessary. The system is equipped with a thermal overload to help prevent severe damage. 4. Turn on water

No. 1 2 3 4 5 7 8 9 10 11 12 13 15 16 17 18 Part No. Description Qty. 116299 ENGINE, gasoline, 6.5 HP Briggs and Stratton 1 244749 PUMP, water, 2700, complete 1 244767 KIT, frame, includes wheels, feet and tip grommets 1 244784 GUN 1 244783 HOSE, 4000 1 804511 WHEEL, pneumatic 2 805535 TIP, spray, red, 0° 1 805536 TIP, spray, yellow, 15° 1 805537 TIP, spray, green, 25° 1 805538 TIP, spray, white, 40° 1 244768 KIT, tip, 4-pack 1 805634 TIP, spray, chemical 1 804275 TUBING, chemical, 5/16 in. ID x

See Installing and Changing Spray Tips (page 12). Pump running too long without spraying Never run pump more than 10 minutes without spraying. Running pump dry Do not run pump without water. Strong surging at inlet and low pressure on discharge side Foreign particles in inlet or discharge valve or worn inlet and/or discharge valves Clean or replace valves. Water spitting out of thermal valve Pump running too long without spraying Trigger gun to get fresh, cooler water in pump. Note: For complete

5. Be sure spark plug ignition cable is pushed firmly onto spark plug. 6. For Model 2525LD ONLY, move throttle to Rabbit (fast) position first. For all models, (then) move choke to CHOKE position. ti3240a ti3242a Model 2525 Only All models 7. Pull the starter rope quickly to start the engine. Pull and return the rope until the engine starts. HINT: Placing one foot on the pressure washer as a brace provides better leverage. NOTE: For easier starting, have one person start pressure washer while an

G–Force Direct-Drive Pressure Washer 2525LD Model 246601, Series A & Series B 2300 psi (159 bar, 15.8 MPa) Maximum Operating Pressure 2500 psi (172 bar, 17.2 MPa) Maximum Working Pressure 2626LD Model 249065, Series A 2600 psi (179 bar, 17.9 MPa) Maximum Operating Pressure 2750 psi (191 bar, 19.0 MPa) Maximum Working Pressure ti6075a ti3224b 2525LD 2626LD GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 2003 GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001 Table of Contents S

290013 LABEL, warning 1 13 116968 WHEEL 2 33. 290131 LABEL, warning 1 14 101242 RING, retaining 2 34. 802363 LABEL, caution 1 15 15C305 FRAME, leg. Series A 1 35 100270 SCREW, cap, hex hd 2 287609 FRAME, leg. Series B 1 36 102040 NUT, lock 2 16 113817 FOOT, base, rubber 2 40 116411 SPRING 2 17 100057 SCREW, hex, cap 2 45 100527 WASHER 4 55 249101 KIT, coupling, hose (see 1 page NO TAG) 56 113418 O–RING 1 . Additional danger and warning tags and labels available free. . Repair parts for Honda Eng

The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR C