Follow manufacturers recommendations. Do not use chlorine bleach or any other corrosive compound. • Some cleaning fluids contain substances which could cause injury to skin, eyes, or lungs. HAZARD RISK TO FLUID INJECTION HOW TO PREVENT IT WHAT CAN HAPPEN • Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection i

To learn more about Porter-Cable visit our website at: The Model and Serial No. plate is located on the frame. Record these numbers in the spaces below and retain for future reference. Model No. Type Serial No. ® Copyright © 2004 Porter-Cable Corporation Part No. A07708-0412-0 2- ENG A07708 SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help

HAZARD RISK OF CHEMICAL BURN HOW TO PREVENT IT WHAT CAN HAPPEN • Use of acids, toxic or corrosive chemicals, poisons, insecticides, or any kind of flammable solvent with this product could result in serious injury or death. • Do not use acids, gasoline, kerosene, or any other flammable materials in this product. Use only household detergents, cleaners and degreasers recommended for use in pressure washers. • Wear protective clothing to protect eyes and skin from contact with sprayed materials. H

NOTE: Using a pump protector/ winterizer or *RV antifreeze is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. PRESSURE WASHER 1. Drain all water from high pressure hose. 2. Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun holder. 3. Store chemical hose so it is protected from damage. 1. Obtain a funnel, six ounces of *RV antifreeze, and 16

Pumps damaged due to chemicals will not be covered under warranty. NOTE: Chemicals and soaps will not siphon when spray wand is in the high pressure setting. A09608 12-ENG STARTING 8. Start engine. See Engine Prior to starting, refer to your engine manual for proper starting procedure. 1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners M

Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the spray wand from the gun. 4. Remove the high-pressure nozzle from the spray wand. Remove any obstructions with the nozzle cleaning tool provided and backflush with clean water. 5. Direct water supply into spray wand to backflush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun and turn on water supply. 8.

Improper control of gun/wand can result in injuries to self and others. HAZARD RISK OF INJURY FROM SPRAY WHAT CAN HAPPEN HOW TO PREVENT IT • Always wear ANSI approved Z87 safety glasses.Wear protective clothing to protect against accidental spraying. • Never point wand at, or spray people or animals. • Always secure trigger lock when wand is not in service to prevent accidental operation. • Never permanently secure trigger in pull back (open) position. • High velocity fluid spray can cause objec

Turn the turret to the desired nozzle. 3. Pull quick connect coupler back and place nozzle into quick connect coupler. 3. Push quick connect coupler over nozzle to secure in place. HOW TO SIPHON CHEMICALS/CLEANING SOLVENTS Siphoning chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To siphon chemicals: 1. Press chemical hose onto barbed fitting located near high pressure hose connection of pump as s

PRESSURE WASHER TERMINOLOGY PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc. GPM: Gallons Per Minute. The unit of measure for the flow rate of water through the pressure washer. CU: Cleaning Units. GPM multiplied by PSI. Bypass Mode: In Bypass Mode, the pump is recirculating water because the trigger of the spray gun is not pulled. Chemical Injection: Feeds cleaning agents into the pump to mix with the pressurized water and

. . . . . . .16 T TTR RRO OOU UUB BBL LLE EES SSH HHO OOO OOT TTI IIN NNG GG G GGU UUI IID DDE EE . . . . . . . . . . . . .17-18 W WWA AAR RRR RRA AAN NNT TTY YYS SST TTA AAT TTE EEM MME EEN NNT TT . . . . . . . . . . . . . . . . . .19 Q QQU UUI IIC CCK KKF FFA AAC CCT TTS SS . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Read Operator’s Manual. Do not operate equipment until you have read Operator’s Manual for Safety, Assembly, Operation, and Maintenance Instructions. This product may