Manual de usuario Yamaha, modelo CL5
Fabricar: Yamaha
Tamaño del archivo: 4.57 mb
Nombre del archivo:
Idioma del manual:
|
 
|
|
|
Enlace gratuito para este manual disponible en la parte inferior de la página
Otros manuales para este modelo:
Resumen del manual
You can set this to the center position by holding down the (< >) key of the computer keyboard and clicking the knob. You can select Pan or Balance for ST IN. The BALANCE knob adjusts the balance of the signal that is sent from the ST IN channel to the STEREO bus L/R channels. PAN/BALANCE can be switched with the [PAN]/[BALANCE] buttons. CSR (Center Side Ratio) Adjusts the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0–100%. CL Editor Owner’s Manual 28 . .) 12 4 7 8 9 0 3 5 6 A 1 LIBRARY Accesses the INPUT EQ page of the Library window. 2 ON Switches the EQ (Parametric Equalizer) on/off of the currently selected channel. 3 EQ graph Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down the (< >) key of your computer keyboard and click the graph (The HPF setting will remain.) 4 Q These knobs adjust the Q level of the frequency range selected in the EQ graph. 5 FREQ (FREQUENCY) These knobs adjust the center frequency for the four bands LOW, LO-MID, HI-MID, and HIGH. 6 GAIN These knobs adjust the Q, center frequency, and boost/cut amount for the four bands LOW, LO-MID, HI-MID, and HIGH. 7 HIGH shelving If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disappear.) 8 LPF (Low Pass Filter) If this button is on, the HIGH EQ will function as a low pass filter. The Q knob of the HIGH EQ will disappear, and the GAIN knob will act as the low pass filter on/off switch. 9 LOW shelving If this button is on, the LOW EQ will be switched to a shelving type (the Q knob of the LOW EQ will disappear.) 0 TYPE I/TYPE II (EQ type) Selects either TYPE I or TYPE II as the EQ type. A ATT (Attenuation) Adjusts the amount of attenuation for the signal level of pre EQ. CL Editor Owner’s Manual 29 . . You can select one of the following types for each of the two dynamics processors. DYNAMICS1 GATE, DUCKING, COMPRESSOR, EXPANDER DYNAMICS2 COMPRESSOR, COMPANDER-H, COMPANDER-S, DE-ESSER If GATE/DUCKING is selected 51 23 6 7 8 4 9 0 BC 1 TYPE Indicates the type of the currently selected gate/ducking. You can click here to select the type. Ducking is the effect that activates compressor triggered by another sound source. 2 LIBRARY This button accesses the dynamics library. Clicking this button will open the DYNAMICS page of the Library window. 3 ON This button switches on/off for the gate or the ducking. 4 Response curve Indicates the response for the gate/ducking of the currently selected channel. 5 GR meter (Gain Reduction meter) This meter indicates the amount of gain reduction produced by the gate/ducking. 6 THRESH (Threshold level) Specifies the level (the threshold level) at which the gate/ducking will activate. The gate will open (or the ducking will activate) when the key-in signal exceeds this level, and the gate will close (or the ducking will deactivate) when the signal falls below this level. 7 RANGE Specifies the amount by which the signal is attenuated while the gate is closed (or while the ducking is activated.) 8 DECAY Specifies the time over which the gate will close (or the time to return to normal signal gain of ducking) after the hold time has elapsed. 9 ATTACK Specifies the time from when the key-in signal exceeds the threshold level until the gate opens (or from when the ducking has been triggered until the signal is ducked.) 0 HOLD Specifies the time that the gate will remain open (or the ducking will remain activate) after the key-in signal falls below the threshold. A CL Editor Owner’s Manual 30 A A Click this to select one of the following signals to use as the key-in source. SELF PRE EQ The pre-EQ signal of the currently selected input channel SELF POST EQ The post-EQ signal of the currently selected input channel MIX OUT 21–24 The output signal of the corresponding MIX channel immediately before the output attenuation CH 1–72 POST EQ The post-EQ signal of the corresponding input channel (however, you can only choose channels belonging to the same group, within the eleven groups CH1–8, CH9–16, CH17–24, CH25–32, CH33–40, CH41–48, CH49-56, CH57-64, CH65-72, STIN1L–STIN4R, and STIN5L–STIN8R) STIN1L–STIN8R POST EQ B CUE This button cue-monitors the currently selected key-in signal. This is not shown in the Additional View. NOTE If the Channel Select/Sends On Fader checkbox in the System Setup dialog box is not checked, the [CUE] button will be hidden in the screen. C KEY IN FILTER Select the type of filter applied to the selected key-in signal; HPF (high pass filter), BPF (band pass filter), or LPF (low pass filter.) The ON/OFF button switches the filter on/off. If you’ve selected BPF, use the two knobs to adjust the band pass frequency and Q. If you’ve selected HPF or LPF, use the knob to adjust the cutoff frequency. If COMPRESSOR/EXPANDER is selected 51 23 4 B 6 7 8 9 0 A 1 TYPE Indicates the currently selected compressor or expander. You can click here to se...
Otros modelos de este manual:
Instrumentos Musicales - CL1 (4.57 mb)
Instrumentos Musicales - CL3 (4.57 mb)
Instrumentos Musicales - Rio1608-D (4.57 mb)
Instrumentos Musicales - Rio3224-D (4.57 mb)
)
