The pressure adjusting valve can be used to set approximate pressure between 10 and 125 P.S.I. (125 P.S.I. is the highest pressure this compressor will deliver). It is normal for the adjustable pressure valve to release air during operation. ALWAYS SET THE PRESSURE VALVE AT OR BELOW THE REQUIRED PRESSURE FOR THE ACCESSORY BEING USED BEFORE STARTING YOUR COMPRESSOR. FOR INFLATION OR OTHER USES REQUIRING ACCURATE PRESSURE, USE A PRESSURE GAUGE. INSTALLATION AND BREAK-IN PROCEDURES Location of the

Usar solo un fusible o interruptor de circuito del mismo amperaje que el circuito en el cual esta operando el compresor de aire. Si el compresor de aire esta conectado a un circuito protegido por fusibles, usar unicamente fusibles de retardo de doble elemento, tal como se indica en la tabla de especificaciones. La instalacion inadecuada de esta unidad puede anular la garantia y su seguro contra incendios. Hacer que el cableado lo haga un electricista calificado que este familiarizado con el codi

Never operate the compressor with guards or covers which are damaged or removed. Attempting to operate compressor with damaged or missing parts or attempting to repair compressor with protective shrouds removed can expose you to moving parts and can result in serious injury. Any repairs required on this product should be performed by authorized service center personnel. HAZARD WARNING: RISK OF FALLING WHAT CAN HAPPEN HOW TO PREVENT IT A portable compressor can fall from a table, workbench, or ro

• Some materials such as adhesives and tar, contain chemicals whose vapors could cause serious injury with prolonged exposure. • Always wear MSHA/NIO5H approved, properly fitting face mask or respirator when using such tools. • Always work in a clean, dry, well ventilated area. RISK OF INJURY • Tools left unattended, or with the air hose attached can be activated by unauthorized persons leading to their injury or injury to others. • Power tools can throw materials through out the work area. • Po

@ 7000 RPM’s Maximum Working Pressure 90 PSI Air Inlet 1/4” NPT Recommended Hose Size 3/8” I.D. Minimum CFM Required @ 90 PSI 8 CFM (25% usage) #1 Approximately 150 ft./lbs. Torque #2 Approximately 190 ft./lbs. Torque #3 Approximately 210 ft./lbs. Torque #4 Approximately 230 ft./lbs. Torque TORQUE REGULATOR KNOB 1 3 4 2 Lubrication Air tools require lubrication throughout the life of the tool. The air motor and bearing uses compressed air to power the tool. Because moisture in compressed a

• The valve is a back pressure regulator which can maintain a steady discharge pressure, however the majority of packages with our modules are controlled through suction gas recycle. Also, most packages have a back pressure regulator on the discharge of our modules to control the actual discharge pressure to a minimum of 70 PSIG. • The presence of the valve was thought to protect the end user in case the discharge of our module is isolated from the skid-level pressure relief valve and the other

• The overloads must be configured for manual reset. • Normal full load run current for each Compressor on the module at 4800 rpm (80 Hz) is approximately 23A. • The customer control circuit must supply an Enable signal to the VFD before the drive will accept a Run Fwd signal. • The VFD will start when the Enable signal is on and a Run Fwd signal is applied. • The VFD will stop if the Run Fwd signal is off or the Enable signal is removed. NOTE The drive provides 24V for the Enable and Run Fwd si

If it contains the solvents listed do nized parts. You must either change the material you Read and follow the safety instructions provided on the label or safety data sheet for the material you are spraying. Use a respirator mask if there is a chance of tions . . . be sure that the respirator mask is suitable for y Electricity Your air compressor is powered by electricity. Like any other electrically powered device, if it is not used properly it may cause electrical shock. Always unplug the air

THIS WARRANTY DOES NOT COVER: . Merchandise sold as, reconditioned, floor models and/or display models sold "as is", any damaged or incomplete equipment sold "as is". . Merchandise used as "rental" equipment. . Merchandise that has become inoperative because of ordinary wear, misuse, negligence, accident, improper and/or unauthorized repair or alterations including failure to operate the product in accordance with the instructions provided in the Owners Manual (s) supplied with the product. . An

Figure 9 Oil Cooling and Thermal Valve A B C Oil Cooler Return 1st-Stage Separator to Compressor 12 2008SSD-34 (5/11) Single-Compressor Module Installation 2.6.3 Compressor Module Motor Protection Variable Speed Compressor Module Protection • The VFD provides overload protection for the compressor. • Module capacity can be changed by varying the typical Compressor speed, ranging from 2400 to 4800 rpm. Figure 10 Motor Control 13 2008SSD-34 (5/11) Single-Compressor Module Installation 2.6.4 Electr