Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 8   Tamaño del archivo: 2 mb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

3. Heaters, if used: refer to Viscon HP Heater manual, 309524. 4. Air compressor: follow manufacturer’s recommendations. 5. Spray gun: ground through connection to a properly grounded fluid hose and pump. 6. Fluid supply container: follow your local code. 7. Object being sprayed: follow your local code. 8. Solvent pails used when flushing: follow your local code. Use only metal pails, which are conductive, placed on a grounded surface. Do not place the pail on a nonconductive surface, such as pa

Descargado: 12   Tamaño del archivo: 470 kb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

The 20:1 King Pump develops 1800 psi (124 bar) MAXIMUMWORKING PRESSUREat 90 psi(6 bar) air pressure. Never exceed these pressures. Be sure that all spray/dispensing equipment and accessories are rated towithstand the maximum working pressure of the pump. DO NOT exceed the maximum working pressure of any component or accessory used inthe system. CHECK all spray/dispensing equipment regularly and repair or replace worn or damaged parts immediately. Always wear protective eyewear, gloves, clothing

Descargado: 25   Tamaño del archivo: 2 mb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

86 MM, 8.6 E 125 @/¥5%^ ( 0. 86 MM > 8.6 E )m^SHAnS^ 0 + ZL200680027833.0 1910678 2413096 89254 ft 93051 1050A^M t i13946a 1050S 1050H t i14342a C€© H003 PROVEN QUALITY. LEADING TECHNOLOGY ..................2 tt«**:..................3 ............. 3 ...................4 ATEX ..................5 »ft ....................5 ..................8 ia ....................10 .................10 .............10 DataTrak.................13 ia±0®................13 + ..............

Descargado: 6   Tamaño del archivo: 470 kb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

Install a fluid drain valve (H) close to the pump fluid outlet. Then connect a grounded fluid supply hose (L). Between the fluid supply hose (L) and the gun/dispensingvalve (K), install a whip hose (M) for greater flexibility. NOTE: To use the optional fluid outlet at the base of the air motor, connect a riser tube between the standard outlet and the optional outlet. GROUNDING WARNING Before operating the pump, ground the system asexplained under FIRE OR EXPLOSION HAZARD and Grounding on page 3.

Descargado: 4   Tamaño del archivo: 470 kb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

x 1.5” (38 mm) long 1 42 100–104** PIN, cotter; 0.125” (3.2 mm) dia. x 1.75” (45 mm) long 1 44 101–712 NUT, lock; 5/8–11; w/nylon insert 3 45 101–936 NUT, hex, jam; 3/4” 1 47 158–674** O–RING, nitrile rubber 1 49 168–211 COUPLING, connecting rod Model 222–248 only 1 161–543 COUPLING, connecting rodModels 215–873 & 204–287 only 1 50 168–210 NUT, shouldered Model 222–248 only 1 161–544 NUT, shouldered Models 215–873 & 204–287 only 1 52 168–824 ROD, tie; 13–7/8” (352.4 mm) long, shoulder to shoulde

Descargado: 46   Tamaño del archivo: 179 kb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

234156 60 psi (4.1 bar) Maximum Working Pressure a Pressure Relief Procedure A-A. To reduce the risk of serious bodily injury, including electric shock and splashing fluid in eyes, follow this procedure whenever you stop spraying: 1. Shut OFF air source. 2. Disconnect power source. 3. Turn gun air valve ON. A WARNINGS Pressurized Equipment Hazard Fluid from gun, leaks or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure

Descargado: 3   Tamaño del archivo: 5 mb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

Perform Pressure Relief Procedure, see page 4. Unplug power cord. 2. Release hopper adapter clamp (158). 3. Loosen rod clamp knob (112) on front of pump module and push rod down. 4. Lift and pull power module (153) off of unit. NOTE: Power module weighs approximately 85 lb. 5. Install hopper plug (117) if needed. Installation 1. Remove hopper plug (117) if installed. 2. Replace power (153) module and insert pump outlet into hopper inlet. 3. Pull rod clamp up and tighten knob (112) on front of pu

Descargado: 19   Tamaño del archivo: 930 kb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

253704, Series B 3:1 Ratio Air-operated Double Diaphragm Pump, with BSPP Fittings Part No. 253705, Series B 3:1 Ratio Air-operated Double Diaphragm Pump, with NPT Fittings 100 psi (0.7 MPa, 7 bar) Maximum Air Input Pressure 300 psi (2.1 MPa, 21 bar) Maximum Fluid Working Pressure Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. TI2125A Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2006, Graco Inc. is registered to I.S. EN I

Descargado: 19   Tamaño del archivo: 470 kb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

3/4 npt(f) inlet and outlet. ACCESSORIES CONTINUED ON THE NEXT PAGE . 306–646 ACCESSORIES USE GENUINE GRACO PARTS AND ACCESSORIES Mustbe purchased separately. GRACO THROAT SEAL LIQUID FLOOR STAND KIT 222–699 Non–evaporating liquid for wet cup Provides secure floor mounting for pump when used with bulk fluid containers. 3” npt fluid inlet. Includes instruc206– 995 1 quart (0.95 liter) tions. (Part nos. 185–443 Ring and 185–445 Plate, in206– 996 1 gallon (3.8 liter) cluded in the kit, are not used

Descargado: 57   Tamaño del archivo: 470 kb   Fabricar: Graco  
Categoría: Equipos de Bombeo
@name

Obstructed fluid hose or gun/valve Fluid dried on the displacement rod Dirty or worn air motor parts Refill and reprime or flush. Clear; see TECHNICAL DATA on back cover. Open, clear. Clear.* Clean. See SERVICE. Clean, service. See air motor manual, supplied. Pump operates but outputlow on both strokes Exhausted fluid supply Restricted line or inadequate air supply Insufficient air pressure, closed or clogged airvalves, etc. Obstructed fluid hose or gun/valve Bleeder valve open or worn Air leaki





Categoría