METAL HEAD Commercial grade metal valve and head EASY TO READ PRESSURE GAUGE Provides fire extinguisher status at a glance. Needle in green means product is ready to use, in red, it needs to be recharged or replaced. BRACKET INCLUDED Plastic mounting bracket with strap for easy mounting. MARINE APPROVED U.S. Coast Guard approved for marine use when used with supplied bracket. CAT. FE10GO Rechargeable Garage/Home UL Rated: 10-B:C FIRE EXTINGUISHER UL 711 Standards UL 299& Listed to First Alert Mo

• On a clean, dry surface where the temperature does not go above 120° F (49° C) or below –40° F (–40° C). HOW TO INSTALL THIS EXTINGUISHER NOTE: Since wall surface types vary, mounting screws are not included. Purchase screws or bolts specifically designed for the surface on which you will mount the fire extinguisher. The fire extinguisher label lists its maximum weight. Mounting screw head type should be #8 pan on round head screws with #8 flat washers. INSTALL THE MOUNTING BRACKET ON A WALL 1

2. Multi-Family or Mixed Occupant Residence: Apartment building, condominium. This Smoke Alarm is suitable for use in individual apartments or condos, provided a primary fire detection system already exists to meet fire detection requirements in common areas like lobbies, hallways, or porches. Using this Smoke Alarm in common areas may not provide sufficient warning to all residents or meet local fire protection ordinances/regulations. 3. Institutions: Hospitals, day care facilities, long-term h

The sounders are powered and actuated as modules via the ADM loop with Apollo/Discovery protocol. They can be used in combination with a detector or strobe, or as stand-alone device. For the latter case an optional white or red plastic lid is available. Furthermore, the sounders are equipped with an integrated dual-isolator module. Two different tone types, depending on the sounder model, are available, and they can be selected during parameterisation of the Fire Detection Control Panel Se- ries

7 5. Test smoke alarm for proper operation (see ”WEEKLY TESTING OF YOUR SMOKE ALARM” section). The smoke alarm operates on a 9-volt battery. The normal battery operating life will be one (1) year. The life of some batteries may be less. 6. Firex smoke alarms sold with Ultralife long-life lithium batteries require replacement approximately every ten (10) years. Replace the battery approximately every ten (10) years or when the low battery signal sounds. !CAUTION: YOU SHOULD ONLY USE THE BATTERIES

This user’s manual contains important information about your Carbon Monoxide (CO) Alarm’s operation. If you are installing this CO alarm for use by others, you must leave this manual—or a copy of it—with the end user. 120V AC ~ 60 Hz 0.09A Reliable Protection, Maximum Convenience! • Just install the battery, plug the alarm into a regular outlet, test, and it’s ready to go! • Battery back-up keeps alarm working if electricity fails. • Test or silence the alarm with a single push of most household

COLOCACION 23 ESPAGNOL SD90TM 21 7. INSTALACION 8. .QUE PASA EN CASO DE ALARMA? 24 9. CAMBIO DE LA PILA 24 10. AJUSTAR EL ENFOQUE INICIAL 24 11. CAMBIAR LA DIRECCION DEL DETECTOR DE HUMO 25 12. PREGUNTAS FRECUENTES 25 13. DATOS TECNICOS 26 1 INFORAMCION GENERAL Y FUNCIONAMIENTO El detector de humo detecta desde el incendio de inicio con bajas temperaturas al incendio violento con formacion de humo y puede instalarse en toda habitacion. El detector de humo utiliza un sensor optico. Este detector

Secure cable to back side of cable tray using three snap-in wire ties. 15. In the Electrical/Compressor section, install snap bushing in the center knockout underneath the terminal strips located in the bottom right-hand corner of control box. 16. Connect wires to terminal strips as shown in Fig. 6 for ComfortLinkt units or Fig. 7 for Electro- --Mechanical Units. NOTE: This step is not needed with 48/50PG Humidi- --MiZert units because they have plug 19 harness already installed in the control b

For special applications a range of accessories (for moist room, false cei- ling or flush installation) is available Specifications Ambient temperature -30°C to +70°C Relative humidity 0 - 95% (no condensation) Colour cream Detector Base B501 Dimensions 0 x H 102 x 20 (mm) Weight 53g Order number 246002 Order name Detector Base/Anal./500/200/SS B501 Detector Base B501DG Dimensions 0 x H 102 x 26 (mm) Weight 57g Order number 246015 Order name Detector Base/Anal./500/200/SS