Here is a check list of things to do in the order we recommend. Mechanical • Uncrate and check for shipping damage both obvious and hidden. Write a damage report and report immediately to the carrier. • Check the serial plate behind the front panel. To do this, remove the front panel by unscrewing the two screws in the upper right and left corners. Next unscrew the two fasteners securing the hinged lower font panel in place. Note the burner inputs shown on the serial number plate. It may be nece
These are required if service technicians need to check a thermocouple without a J calibrated temperature meter. Check the thermocouple if you find the temperature variation of the thermostat is more than ± 5.F from the set point. To check a thermocouple, follow this procedure: Note: The Type J thermocouple requires the use of a Type J temperature meter. If a type J meter is not available use a millivolt meter and refer to the tables of degrees/millvolt values following, to calculate the cold ju
Excessive heat causes grease to carbonize and makes the surfaces hard to clean. 3. Empty the grease trays often to avoid spillovers. 4. For extended shutdown or major maintenance, turn the power and zone switches OFF, close the manual shut-off gas valve, and unplug the electrical power cord. Cleaning 1. At the end of the cooking operations, wipe and clean the unit while it is still warm. Use a spatula to remove food residue and burnt grease. 2. When the plate is cool, wash it with a mild deterge
The thermocouple detects changes in temperature, but because of the short circuit it may fail to register the set temperature at the thermostat. This means the burner may not shut off. At the other extreme, the short circuit may occur in a place not shielded from the flue gases, which means the burner may shut off prematurely. These are the two conditions to look for in a shorted thermocouple. Deterioration from aging and from welding dissimilar metals together to for a junction introduces a con
Inhalation of airborne particles of glass wool/ceramic fibers is known to the state of California to cause cancer. Operation of this product could expose you to carbon monoxide if not adjusted properly. Inhalation of carbon monoxide is known to the state of California to cause birth defects or other reproductive harm. Keep appliance area free and clear of combustibles. Part #GCGTRAINING06 (03/03/08) Page TABLE OF CONTENTS IMPORTANT INFORMATION 2 DIMENSIONS AND SPECIFICATIONS . 4 WHAT IS A CHAIN
High performance, high volume production with even, consistent, controlled temperatures 100° to 450° F (40°-230°C) range. 3/4" (19mm) thick griddle plate, with 24" (610 mm) deep grilling surface. Garland has designed this heavy-duty griddle to give the features required for high-volume operations. Griddles are available with hi-lo valve controls or for temperature set control models with snap action thermostats. G24 griddles with snap action thermostats do not require any electrical connections
PAGE 1 TECHNICAL SPECIFICATIONS ..................... ...................... PAGE 2 GENER AL INSTALLATION ..................... ...................... PAGE 3 INSTALLATION PROCEDURE ..................... ...................... PAGE 4 COMMISIONING ..................... ...................... PAGE 4 OPERATING INSTRUCTIONS ..................... ...................... PAGE 5 MAINTENANCE & CLEANING ..................... ...................... PAGE 6 MANUFACTURED BY: DISTRIBUTED BY: GARLAND COM
Manual Pilot Valve All burners are equipped with constant-burning pilots. These should be manually lighted immediately after the gas is turned on and the system is checked for leaks. An adjustment screw for each pilot is located on the gas manifold and can be accessed through openings in the valve panel between the valve knobs. Testing and Adjustments Check all gas connections for leaks using a soapy solution before lighting any pilots. DO NOT USE OPEN FLAME TO CHECK FOR LEAKS! Putting open flam
Each plate element is controlled by a switch with six heat positions. Elements are protected with a high limit which automatically reduces power to prevent over heating. Standard Features: • Stainless steel front & black painted sides • Two 7-1/2" (192 mm) diameter sealed elements • Each element rated 2000 watts • Each element controlled by a switch with six heat positions that automatically cycles down to a low heat when left unused • Heat-On indicating lamps • 4" (102mm) stainless steel