Use wall straps for this purpose (see Figure 19). Whenever possible, use 45° elbows instead of 90° elbows. The 45° elbow offers less restriction to the flow of the flue gases and intake air. 5. Place the flashing over the pipe section(s) extending through the roof. Secure the base of the flashing to the roof and framing with roofing nails. Be sure roofing material overlaps the top edge of the flashing as shown in Figure 19. There must be a 1" clearance from the vent pipe to combustible materials

Valve (Natural Gas) 1 14570 Electronic Elec. Valve (Propane/LP Gas) 1 17 14253 Flex Gas Line 1 18 11186 Screw, #8-32 x 1 Zinc 2 19 110286-01 Ignition Module, Synetek 1 20 11147 Screw, #10-24 x 1/2 PPH MS Blk 2 21 14129 Transformer 24V Class 1 22 17223 Magnet 2 23 11201 Nut, 8-32 Hex Zinc 4 24 23416 Elect. Components Board 1 25 14120 Spade 1/4 Female Connector 4 26 14134 Wire, 18 GA Black 5 27 14126 Wire, 16 GA TFFN/MTW 1 28 14115 Spade toungu connector 1 29 14149 Spade, 1/4 F R/Angle Connector 4

Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer, service agency or the gas supplier. INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. For more information, visit ik WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct i

If they can't supply original replacement part(s), call DESA Heating, LLC at 1-866-672-6040. When calling DESA Heating, LLC, have ready • your name • your address • model and serial numbers of your firebox • how firebox was malfunctioning • type of gas used (propane/LP or natural gas) • purchase date Usually, we will ask you to return the part to the factory. PARTS NOT UNDER WARRANTY Contact authorized dealers of this product. If they can't supply original replacement part(s), call DESA

The clearances are the same for either installation method. Mantel Clearances for Built-In Installation If placing custom mantel above built-in firebox, you must meet the minimum allowable clearance between mantel shelf and top of firebox opening shown in Figure 7. These are the minimum allowable mantel clearances for a safe installation. Use larger clearances wherever possible to minimize the heating of objects and materials placed on the mantel. A CAUTION: Do not allow the vent-free gas log

Chrome Trim Standard on Whirlpools of all Other Colors. Water Capacity to Overflow: 46 gal. FAUCETS ARE NOT INCLUDED. ALL FIXTURE DIMENSIONS ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY ASME/ANSI STANDARDS, Z124.1. ALL MEASUREMENTS SHOWN ARE SUBJECT TO CHANGE OR CANCELLATION. Whirlpools/Tubs 1.15 Eljer, Inc. 5/07 www.eljer.com

Bath waste not included. NOTE: Eljer assumes no responsibility or liability for local or state regulations which deviate from national standards. It shall be the responsibility of the installer to comply with local codes and standards prior to installation of any Eljer product. Electrical Requirements: 115V, 20AMP, GFCI Protected Circuit ■ 59 3/4" (1518 mm) Length, 32" (813 mm) Width, 18 1/2" (470 mm) Height ■ Six Jetted Multi-Directional Whirlpool System ■ Rectangular Unit with Integral

Bath waste not included. Soaker Tub model also available. NOTE: Eljer assumes no responsibility or liability for local or state regulations which deviate from national standards. It shall be the responsibility of the installer to comply with local codes and standards prior to installation of any Eljer product. Electrical Requirements: 115V, 20AMP, GFCI Protected Circuit HIGH GLOSS ACRYLIC ■ 71 3/4" (1822 mm) Length, 41 1/2" (1054 mm) Width, 23" (584 mm) Height ■ Six Jetted Multi-Direction

Table of Contents OWNER’S MANUAL.........................................................................1 FEATURES OF THE SONIC IMMERSION.................................................1 USING THE CD PLAYER......................................................................1 DEALER INSTALLATION..............................................................2 GETTING READY TO START................................................................3 Overview of the Installation....................