Then turn the power switch Off (O) and unplug the machine. 12 Push the machine to a designated waste water “DISPOSAL SITE” and empty the recovery tank. To empty, pull the Recovery Tank Drain Hose (12) from its rear storage hanger, then remove the plug (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled flow of waste water). Refill the solution tank and continue cleaning. USING ATTACHMENTS To use accessory tools, disconnect the recovery hose at the Recover

No. Qty Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 46734A 40318A 902654 902550 51840A 50520A 56480A 962546 50517A 448396 40826A 55657A 55656A 59805A 50515A 80501A 54238A 1 1 1 1 1 1 2 2 1 4 4 1 1 1 2 1 1 Stator Assembly (w/Magnets & Clips) Armature Asm.(w/B.E. & F.E. bearings) Bearings B.E. Bearing F.E. Commutator Bracket Assembly (w/Brush BRD Assembly Leads) Commutator BracketStrain Relief Brush Board Screw Brush Board Asm. (w/springs & brushes) Brush SpringBrush AssemblyLead Assembl

70935A Nilfi sk ALTO Operator's Manual -SCRUBTEC 770 / 784 / 795 Nilfi sk ALTO SCRUBTEC 770S / 784S / 795S Control Panel Assembly / Solo Speed Controller 12/09 Item 1 2 3 4 Ref. No. 30592A 85815A 980205 85813A Qty 1 2 6 4 DescriptionControl Handle Screw, 5/16-18 x 1 1/2 Washer, 5/16 Flat Screw, 5/16-18 X 1 Item 32 33 34 35 Ref. No. 920208 962968 40749A 47381B Qty 2 2 1 1 DescriptionNut, 1/4-20 Screw, 10-24 x 1/2 Switch, Momentary Rocker Switch, Mantain Rocker5 920110 4 Nut, LK 5/16-18 36 55502A

destiliuota vandeni. Jei naudosite destiliuota vandeni, prailginsite Kiekviena karta pries jungdami prietaiso tarnavimo laika. Valikliai, prietaisa bei po darbiniu pertraukvapiosios medziagos, tirpikliai keliu is purkstuko ispilkite kondenir kitos chemines medziagos gali sata. pazeisti prietaisa ir sukelti sveikaNoredami isvalyti purkstuka, tos sutrikimu. nukreipkite garo srove i koki nors inda arba praustuva ir nuspauskite Reguliariai tikrinkite, ar nepazeiskontroline garo svirtele, esancia tas

The right accessories not only enable the cleaning job to be done in the fastest and most efficient way, they also help to prevent damage to the machine and reduce maintenance cost. All products carrying the Nilfisk-Advance label have been fully tested and are guaranteed for use with our equipment. Specifications and details are subject to change without prior notice. Nilfisk-Advance A/S Sognevej 25 DK-2605 Brondby Denmark Tel.: +45 4323 8100 Fax: +45 4343 7700 96020906-09, © 2005/09 Nilfisk-Adv

_Squeeze filter frame (A) and pull it out until it stops. Do not completely remove frame. Wipe debris off filter. Slide filter back in place. Empty solution tank and rinse thoroughly. Let air dry. Place empty solution tank on carpet cleaner. Turn carpet cleaner ON. Squeeze trigger and push carpet cleaner forward and back several times. This will clear any solution remaining inside the cleaner. Empty recovery tank, rinse thoroughly and let air dry. Remove water from the hose (see "After using too

8. Put the traverse speed switch to the mid range speed setting. As the machine begins to travel down the ramp, maintain a slow downward speed by pressing either of the forward switches. 9. Replace squeegee assembly, brush housings, & brushes or pad drivers after the machine is unloaded and ready to use. Nilfi sk ALTO Operator's Manual -SCRUBTEC 770 / 784 / 795 FORM NO. 70935A - 7 SYMBOLS USED ON SCRUBTEC 770, 784, 795 SYMBOLS USED ON SCRUBTEC 770S, 784S, 795S / 770L, 784L, 795L Hazard Alert Sym

2 MANUAL PURPOSE AND CONTENTS ........................................................................................................... 2 TARGET ........................................................................................................................................................... 2 HOW TO KEEP THIS MANUAL ....................................................................................................................... 2 IDENTIFICATION DATA .............................