MASK ANY AREA YOU DO NOT WISH TO SPRAY. Once you have set up ready to spray, switch on the unit. No paint will be sprayed from the gun until the trigger on the spray gun is pulled. Before starting any work on spraying actual objects we suggest you spend a small amount of time practicing on cardboard or newspaper until you have got used to how the gun works. 11 SPRAY PATTERNS Fig.2 Vertical Jet Round JetHorizontal Jet The gun has 3 different spray patterns – Horizontal, Vertical and Round (Fig.2)

. NUNCA, bajo ninguna circunstancia, debe apuntar con la pistola pulverizadora a una persona o animal. En el caso de que se produzca un accidente con lesiones, acuda a la consulta de un medico inmediatamente. . No deje NUNCAque ninos o personas no autorizadas usen o jueguen con el equipo de pulverizacion. . Lea siempre las instrucciones del fabricante para el rebajado de la pintura antes de utilizarla. . Lleve siempre una mascarilla adecuada cuando efectue la pulverizacion. Tambien recomen damos

• We recommend you wear protective clothing. • Stir the paint well using a mixer where possible. • Make sure there are no solid particles in the paint. • Many products can be sprayed without being thinned. However, if the application is not good, thin the product progressively in stages of 5%. • Most paints can be sprayed by being thinned just a little, e.g. by 5% or 10%. • Some thick paints such as outer wall paints and certain undercoats will need to be thinned by 20% or 25%. • Use water to th

Please retain for future reference. 2 EXPLODED PARTS VIEW 13 14 14 13 Fig.2 12 11 10 9 7 8 4 5 6 2 3 1 A B Fig.1 Fig.3 HV3500 HV2900/ 3900 PARTS LIST FFiigg..11 No.Description Part Code No.Description Part Code 1. Needle and Fluid Tip Tool V0018 7. Fluid Needle 2.0mm V0006 2. Air Cap Ring V0001 8. Lip Seal -Fluid Needle V0007 3. Air Cap V0002 9. Paint Flow Adjuster V0011 4. Spray Direction Plate V0003 10. Paint Container Seal L0682 5. Fluid Tip 2.0mm V0004 11. Pick-up Tube V0012 6. Fluid Tip O-R

2) When you get to the end of the line, release the Trigger for a moment and then apply the product in the opposite direction just beneath the line you have sprayed. 3) Next, to achieve a vertical strip adjust the Spray Direction Plate (4) to the horizontal position then pull the Trigger and move your arm up and down over the horizontal strips you just have sprayed. Through gradual movement of the Spray Direction Plate (4) between Horizontal, Vertical and Round spray pattern you can vary the wid

mostrado en LISTA DE PIEZAS N° Description 1. Anillo del soporte de la boquilla 2. Soporte de la boquilla de aire 3. Placa del distribuidor de aire 4. Boquilla de 2.0mm 5. Sello de la boquilla 6. Tornillo pivote 7. Arandela 8. Ensamblaje del cuerpo principal 9. Aguja del fluido de 2.0mm 10. Adaptador 11. Muelle 12. Tornillo de ajuste 13. Pivote 14. Tubo de alimentaci n de aire 15. Tuerca del prensaestopas LISTA DE PIEZAS N. pieza L0151 L0152 L0162 L0157 L0159 L0179 L0195 L0180 L0166 L0174 L0175

The spray applicator should be thoroughly cleaned after each use. Follow the cleaning instructions on page 9 with reference to the drawings on page 3 ! Check the needle and fluid tip on a regular basis for excessive wear, and replace as necessary. See the cleaning instructions for the correct procedure for removing these parts. Replacement needle sets are available from Earlex Ltd. ! Keep all moving parts lubricated with a light smear of petroleum jelly. ! Lubricate the gland washer, after each

BEFORE USE - PLEASE READ THE SAFETY & OPERATING INSTRUCTIONS. Please retain for future reference N0150 05/05.qxd 27/5/05 10:28 am Page 2 SAFETY INSTRUCTIONS WARNING! FIRE AND EXPLOSION HAZARD. . CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, USE INDOORS ONLY. . The substances used with this spray applicator (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials. ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING US

The round spray is used for small objects or for areas - such as corners – that are difficult to reach. To adjust the spray pattern, loosen the Air Cap Ring (1), adjust the position of the Air Cap (2) to obtain either a vertical, horizontal or round pattern then re-tighten the aircap ring. PAINT VOLUME The volume of paint sprayed is easily adjustable. (Fig.5(a)) Completely close Fluid Adjusting Screw (8) by turning this clockwise as far as it will go. Whilst pulling the trigger, begin turning th

No obstante, algunos materiales no pueden pulverizarse, asi que revise las recomendaciones del fabricante antes de comprar la pintura. Si el material es solo para ser aplicado con brocha, normalmente no puede ser pulverizado. ESTA UNIDAD NO PUEDE USARSE CON PINTURAS CON TEXTURA. EL USO DE DICHOS MATERIALES CAUSARA EL DETERIORO PREMATURO, QUE INVALIDARA LA GARANTIA. PARA OBTENER LOS MEJORES RESULTADOS DE SU SISTEMA DE PINTADO AEROGRAFICO, LE ROGAMOS LEA DETENIDAMENTE LAS INSTRUCCIONES ANTES DE US